Re: [MW:28140] Weld bead length

Dear Steve,

Thanks for your suggestion, but my client asking us to start multi run welding after hot pass, actually we are doing multi run for cover pass. As it is very difficult to weld multi run in narrow groove.

On Fri 27 Jul, 2018, 9:14 AM 'Steve Burik' via Materials & Welding, <materials-welding@googlegroups.com> wrote:

All,

Your client is right, multi bead welding for cover pass - with SMAW - ensures fine grain weld metal and eliminates the risk of undercut which is the result of high amperage and incorrect electrode control.

regards,

Steve Burik, IWE

On ‎Thursday‎, ‎July‎ ‎26‎, ‎2018‎ ‎11‎:‎59‎:‎59‎ ‎AM, Nadakuditi kiran kumar <kinnu78@gmail.com> wrote:

Dear Gentlemen,
We are doing welding of LTCS materials, while welding some of the
joints we welded final run in single bead which is as per approved
WPS(3 x electrode dia.) Our client is asking us to do multi bead
welding above 6" pipe even though the gap in groove is below 9 mm. We
are using 3.15 electrode to do the final run. We are maintaining heat
in put in control. Please clarify me whether it is correct or not?

Thanks & Regards

N.Kiran kumar,

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

[MW:5202] RE: 5200] NDT after PWHT

------------------------------------- Interpretation: I‑89‑14 Subject: Section I (1986 Edition, 1987 Addenda), PW‑11, NDE Prior to PWHT Date Issued: December 15, 1988 File: BC88‑393 Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39? Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation: VIII-1-98-09 Subject: Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE ...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Materials & Welding

Search This Blog