Re: [MW:21989] Weld Repair limitation

Dear Friend,

Some issues like this are related to project spec. Probably in each project we don't have just one or two simple joints, so it has to be defined  in welding and inspection procedures. If it is not applicable for your project (you didn't predict repair situations) you can use repair PQR (something like a production test) which is repaired similar to the actual repair and then qualify this coupon. (You can see DNV OS-F101 for better understanding).

Regards

On Wed, Sep 24, 2014 at 2:48 AM, TDK YOKESH <tdky167@gmail.com> wrote:

Well , is there any supporting document ? Because there is been a situation where a 30" pipe , 31.75WT pipe RT ( R2 ) was rejected as it had 4mm slag and had to be cut out . The production /execution don't want to cut out but repair it . So practically ,  performing a cut out for 4 mm slag is necessary ? In order to convince the client I need to produce supporting document .  

Thanks and Regards 

TDK Yokesh 

On Tue, Sep 23, 2014 at 3:48 PM, S.Mohammed <mohd52100@gmail.com> wrote:

As good engineering practice and keeping joint integrity in place

for high pressure line - 1 time ..after cut out.

low pressure maximum 3 times.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm

The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

--
M. Shokri Arfaei

ISA-ISTS - Metallurgy Lab. Manager

ASNT NDT Level III

International Welding Engineer

Tel.: +98 21 66282127

Fax: +98 21 66282779

Mob.:+98 912 1394023

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.