Fw: RE: Re: [MW:4910] Acceptability of MTC.

Please see below our material controller's comments.He also wants to know which year Code edition is referred to....

--- On Wed, 21/4/10, kehinde.akintulerewa@nigerdock.com <kehinde.akintulerewa@nigerdock.com> wrote:

From: kehinde.akintulerewa@nigerdock.com <kehinde.akintulerewa@nigerdock.com>
Subject: RE: Re: [MW:4904] Acceptability of MTC.
To: nach_sam@yahoo.com
Cc: shola.adeyemi@nigerdock.com
Date: Wednesday, 21 April, 2010, 3:42 PM

Mr. Shank,

I will disagree with the mail below

MTC is a requirement of SA20 Para 19.1

Dish head shall be checked to conform with UG79 & UG81

MTC Shall be verified for conformance with Applicable Edition and Addenda of ASME Sec 11 part A.

Regards,

Kehinde

From: Shashank Vagal [mailto:nach_sam@yahoo.com]
Sent: Wednesday, April 21, 2010 8:13 AM
To: Kehinde Akintulerewa
Subject: Fw: Re: [MW:4904] Acceptability of MTC.

--- On Wed, 21/4/10, Arunachalam A <arunvani@gmail.com> wrote:

From: Arunachalam A <arunvani@gmail.com>
Subject: Re: [MW:4904] Acceptability of MTC.
To: materials-welding@googlegroups.com
Date: Wednesday, 21 April, 2010, 12:48 AM

If the vessel is as Per Div-1, and the end cap is a standard one as per ASME B16.9, you do not not require MTC. The end cap can be accepted based on marking as per UG 11 & UG 93. The manufacturer's marking is taken as the certification of materials.

arun

On Sun, Apr 18, 2010 at 5:59 PM, smruthi mohan <smruthi2007@rediffmail.com> wrote:

Hi.

Anybody please advise me on the below,

we have an 12" End Cap (SA403 WP316L)for an ASME job. But in test certificate there is an additional element content (Cu (0,370))is present in the chemical Analysis. please advice me that we can accept this item or not.

Thanks in advance.

SMRUTHI MOHAN
ENGINEER - MATERIALS.
QICL, FUJAIRAH

Error! Filename not specified.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
ARUNACHALAM.A
050-5257122

IT'S BETTER TO LOSE YOUR EGO TO THE ONE YOU LOVE.
THAN TO LOSE THE ONE YOU LOVE ....... BECAUSE OF EGO
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Please know that this email is confidential and should be read by only the intended receipient

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...

Materials & Welding

Search This Blog