Wednesday, April 28, 2010

RE: [MW:4971] Buttering procedure for P4 to Inconel

In what aspect is NiCrFe2 better than NiCrFe3 at higher temp?

Creep strength?

 

 

 

With kind regards,

Erwin GERING

 

Van: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] Namens kgpandithan
Verzonden: zaterdag 24 april 2010 16:44
Aan: materials-welding@googlegroups.com
Onderwerp: Re: [MW:4946] Buttering procedure for P4 to Inconel

 

Temperature is limiting factor for using NiCrFe3 which has more Mn than NiCrFe2 which is better for higher temp.

NiCrMo3 is best suited for corrosive environment

kgp

On Wed, Apr 21, 2010 at 4:16 AM, pgoswami <pgoswami@quickclic.net> wrote:

 Mr. Ibrahim,

 

Excuse me for my delayed response. A change from ENiCrFe3  to  ENiCrFe2 is not an essential variable as per Sec-IX (same F & A No). Hence as per code there are no issues. However  Ni-Cr-Fe electrodes conforming to  E-NiCrFe3  spec for are more commonly available, and both ENiCrFe2 & ENiCrFe3 have almost matching chemistry and properties (see attached).Hence I would say that qualifying PQR with one brand , preferably E-NiCrFe3  would be  a good option. 

 

As regarding your query on use of ER NiCrMo-3+E NiCrMo-3 electrodes, if the specification calls for the API-582 (see below) requirements to be followed , then you may have to choose this type of welding consumables.

 

Otherwise E/ER-Ni-Cr-Fe-3 should be fine.

 

Table 6-1 Application of Nickel-Based Electrodes in Sulfur and Non-Sulfur Environments

 

AWS Filler Material

Designation

Max. Design Temperature (non-sulfur environment)

Max. Design Temperature (sulfur environment)

ENiCrFe-3

1000 °F (540 ºC)

700 °F (370 ºC)

ERNiCr-3, ENiCrFe-2

1400 °F (760 ºC)

750 °F (400 ºC)

ERNiCrMo-3

1100°F (590 ºC)

900°F (482 ºC)

ER NiCr-4

1100°F (590 ºC)

1100°F (590 ºC)*

               

 Thanks

 

 

Pradip Goswami,P.Eng.

Welding & Metallurgical Engineer/Specialist

Email-pgoswami@sympatico.ca,

pgoswami@quickclic.net

 

 

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of GERING, Erwin
Sent: Thursday, April 15, 2010 2:55 AM
To: materials-welding@googlegroups.com
Subject: RE: [MW:4845] Buttering procedure for P4 to Inconel

Dear Hegde

 

Why not mix up ENiCrFe3  or ENiCrFe2  ?

 

With kind regards,

Erwin GERING

 

Van: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] Namens PB HEGDE
Verzonden: donderdag 15 april 2010 5:32
Aan: materials-welding@googlegroups.com
Onderwerp: RE: [MW:4835] Buttering procedure for P4 to Inconel

 

i)You can butter either by ENiCrFe3  or ENicrF2  individually but no mix up

ii) After buttering on P4 you require to carry PWHT of that buttered components

iii) later on further butt joint  with Inconel ,you need go for PWHT

 

Regards

 

Hegde

 

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Muhammed Ibrahim
Sent: Wednesday, April 14, 2010 12:27 PM
To: materials-welding@googlegroups.com
Subject: Re: [MW:4820] Buttering procedure for P4 to Inconel

 

Dea Sir,

 

I would like to qualify a new PQR for this application. Can I use ENiCrFe2 for buttering & ERNiCr-3 + ENiCrFe2/Fe3 for the buttwelding?.

 

Or I need to go for ER NiCrMo-3+E NiCrMo-3?.

 

Regards,

 

Ibrahim



 

On 13 April 2010 13:46, Bathula Raghuram (Mumbai - PIPING) <R.Bathula@ticb.com> wrote:

You may use Inconel to Inconel PQR for butt weld, however for buttering you require a separate buttering PQR for buttering thickness less than 5mm or a groove weld PQR on P4 material welded with Inconel can be used when your buttering thickness exceeds 5mm. Weld overlay PQR can't be used for buttering.


From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Muhammed Ibrahim
Sent: Tuesday, April 13, 2010 2:36 PM
To: materials-welding@googlegroups.com
Subject: [MW:4804] Buttering procedure for P4 to Inconel

Hi Members,

 

Kindly request your suggestion on the following matter.

 

We have to weld one 2" Nozzle (PNo.4) to Tube sheet with (PNo.4). Due to some practical difficulties we have to avoid PWHT of this joint. So we are planning to buttering both nozzle and tube sheet nozzle opening with Inconel. Then Butt weld the joint with Inconel.

 

We have one overlay procedure (SMAW) with Inconel on P4 material with PWHT and another butt welding procedure for Inconel to Inconel (GTW+SMAW) without PWHT.

 

Can I use these PQR together for this butt weld?.

 

Or I have to qualify a new buttering+buttwelding PQR with same condition?.

Thanks & Regards
Muhammed Ibrahim PK


--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.




--
Thanks & Regards
Muhammed Ibrahim PK

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.


THIS MESSAGE IS ONLY INTENDED FOR THE USE OF THE INTENDED RECIPIENT(S) AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED, PROPRIETARY AND/OR CONFIDENTIAL. If you are not the intended recipient, you are hereby notified that any review, retransmission, dissemination, distribution, copying, conversion to hard copy or other use of this communication is strictly prohibited. If you are not the intended recipient and have received this message in error, please notify me by return e-mail and delete this message from your system. Ontario Power Generation Inc.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

 

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

[MW:34820] RE: 34813] Clarification in Rate of heating and cooling.

Hello,   Please see the response below.   Regards.   P. Goswami, P. Eng, IWE.   From: materials-welding@googlegroups.com <materials-weld...