(a) Except as otherwise provided in UG-4(b), UG-10,
UG-11, or UG-15, requirements for acceptance of materials
furnished by the material manufacturer or material supplier
in complete compliance with a material specification of
Section II shall be as follows.
(1) For plates,the vessel Manufacturer shall obtain
the material test report or certificate of compliance as provided
for in the material specification and the Inspector
shall examine the Material Test Report or certificate of
compliance and shall determine that it represents the material
and meets the requirements of the material specification.
(2) For all other product forms, the material shall be
accepted as complying with the material specification if
the material specification provides for the marking of each
piece with the specification designation, including the
grade, type, and class if applicable, and each piece is so
UG-11 PREFABRICATED OR PREFORMED
PRESSURE PARTS
(a) Cast, Forged, Rolled, or Die Formed Standard Pressure
Parts
(1) Pressure parts, such as pipe fittings, flanges, nozzles,
welding necks, welding caps, manhole frames and
covers, that are wholly formed by casting, forging, rolling,
or die forming shall not require inspection, identification
in accordance with UG-93(a) or (b), or Partial Data Reports.
Standard pressure parts that comply with some ASME standard
Division or of materials specifically listed in an ASME
product standard listed elsewhere in this Division. Standard
pressure parts that comply with a Manufacturer's standard6,7
shall be made of materials permitted by this Division.
Parts made to either an ASME standard or
Manufacturer's standard shall be marked with the name
or trademark of the parts manufacturer and such other
markings as are required by the standard. Such markings
shall be considered as the parts Manufacturer's certification
that the product complies with the material specifications
and standards indicated and is suitable for service at the
rating indicated.
SA 20 is for pressure vessel plates, not for standard fittings.arunOn Wed, Apr 21, 2010 at 2:29 PM, Shashank Vagal <nach_sam@yahoo.com> wrote:
Please see below our material controller's comments.He also wants to know which year Code edition is referred to....
--- On Wed, 21/4/10, kehinde.akintulerewa@nigerdock.com <kehinde.akintulerewa@nigerdock.com> wrote:
From: kehinde.akintulerewa@nigerdock.com <kehinde.akintulerewa@nigerdock.com>
Subject: RE: Re: [MW:4904] Acceptability of MTC.
To: nach_sam@yahoo.com
Cc: shola.adeyemi@nigerdock.com
Date: Wednesday, 21 April, 2010, 3:42 PM
Mr. Shank,
I will disagree with the mail below
MTC is a requirement of SA20 Para 19.1
Dish head shall be checked to conform with UG79 & UG81
MTC Shall be verified for conformance with Applicable Edition and Addenda of ASME Sec 11 part A.
Regards,
Kehinde
From: Shashank Vagal [mailto:nach_sam@yahoo.com]
Sent: Wednesday, April 21, 2010 8:13 AM
To: Kehinde Akintulerewa
Subject: Fw: Re: [MW:4904] Acceptability of MTC.
--- On Wed, 21/4/10, Arunachalam A <arunvani@gmail.com> wrote:Date: Wednesday, 21 April, 2010, 12:48 AM
From: Arunachalam A <arunvani@gmail.com>
Subject: Re: [MW:4904] Acceptability of MTC.If the vessel is as Per Div-1, and the end cap is a standard one as per ASME B16.9, you do not not require MTC. The end cap can be accepted based on marking as per UG 11 & UG 93. The manufacturer's marking is taken as the certification of materials.
arun
On Sun, Apr 18, 2010 at 5:59 PM, smruthi mohan <smruthi2007@rediffmail.com> wrote:
Hi.
Anybody please advise me on the below,
we have an 12" End Cap (SA403 WP316L)for an ASME job. But in test certificate there is an additional element content (Cu (0,370))is present in the chemical Analysis. please advice me that we can accept this item or not.
Thanks in advance.
SMRUTHI MOHAN
ENGINEER - MATERIALS.
QICL, FUJAIRAH--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
ARUNACHALAM.A
050-5257122
IT'S BETTER TO LOSE YOUR EGO TO THE ONE YOU LOVE.
THAN TO LOSE THE ONE YOU LOVE ....... BECAUSE OF EGO--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
Please know that this email is confidential and should be read by only the intended receipient
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
ARUNACHALAM.A
050-5257122
IT'S BETTER TO LOSE YOUR EGO TO THE ONE YOU LOVE.
THAN TO LOSE THE ONE YOU LOVE ....... BECAUSE OF EGO
--
ARUNACHALAM.A
050-5257122
IT'S BETTER TO LOSE YOUR EGO TO THE ONE YOU LOVE.
THAN TO LOSE THE ONE YOU LOVE ....... BECAUSE OF EGO
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
Comments