Skip to main content

Re: [MW:4972] about boron content in SA 516 grade 70 plates

By Materials & Welding

Dear Sir

With reference ur mail on nov 30 2009 you told that it is ok if it is upto 0.003% and what difference it make if there is boron in the plates is excessive amount can you give me any detailss weather it can be use or not or any thing related to this in astm books

 

Monday, November 30, 2009

[MW:3769] RE: SA 516 GR 70 plates-Boron content- clarification

Boron can significantly increase the hardenability of steel without loss of ductility. Its effectiveness is most noticeable at lower carbon levels. The addition of boron is usually in very small amounts ranging from 0.0005 to 0.003 %; usually fastener steels contain boron for hardenability. Check hardness?

Refer UG 10 if it is a div1 vessel "consideration should be given to making analyses for elements not specified in the specification but that would be deleterious if present in excessive amounts"

May be you can ask the plate mill, what is excessive amount?

From: Qamlr [mailto:qamlr@cicb-chemicon.com]
Sent: Monday, November 30, 2009 2:35 PM
To: materials-welding@googlegroups.com
Subject: SA 516 GR 70 plates-Boron content- clarification

 

Dear All

 

As per the SA 516 GR 70, boron content is not specified and shall not be present as specified element. For SA 516 GR 70 plate  manufacturer certifies that this element is within permissible limit

 

Kindly give your suggestions to what basis we can certify for Coded vessels being constructed

 

Also kindly brief as to why the presence of boron and its affect??

 

 

Thanks in advance & regards

 

Prashanth Hegde

Head Quality

Regards,
 
Vikas Dinesh Shah

 

----- Original Message -----
From: Qamlr
Sent: Wednesday, April 28, 2010 11:55
Subject: RE: [MW:4970] about boron content in SA 516 grade 70 plates

Dear Mr. Vikas

 

Boron requirement as an unspecified element  shall not exceed 0.0005 percent ( as per SA 941 under discussion chapter).

 

Regards

 

Prashanth Hegde

Head Quality

CICB-Chemicon Pvt. Ltd

 

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Vikas Shah
Sent: Wednesday, April 28, 2010 11:48 AM
To: materials-welding@googlegroups.com
Subject: [MW:4969] about boron content in SA 516 grade 70 plates

 

Dear Sir

 

 

Is boron allowed in the SA516 grade 70 plates upto 0.0014%

 

 

 

Regards,

 

Vikas Dinesh Shah

 

Sanghavi Bothra Engineering Co. Pvt. Ltd.
56, Kika Street, Gulalwadi,
Mumbai – 400004. India.
Mobile: +91-9821532896
Tel: +91-22-40416200 / Fax: +91-22-23452161
Direct Line: +91-22-40416223
E-mail - vikas@sbecpl.com
Website: - www.sbecpl.com

 

Please consider the environment before printing this e-mail

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.


Please don't print this e-mail unless you really need to.
*******************************************************************
This e-mail is confidential. It may also be legally privileged. If you are not the addressee you may not copy, forward, disclose or use any part of it. If you have received this message in error, please delete it and all copies from your system and notify the sender immediately by return e-mail. Internet communications cannot be guaranteed to be timely, secure, error or virus-free. The sender does not accept liability for any errors or omissions.
*******************************************************************
"SAVE PAPER - THINK BEFORE YOU PRINT!"

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more