Thursday, October 28, 2010

Re: [MW:7904] Surface preparation and coating

Dear Haseeb,
 
While checking the DFT from where do the counting starts when we are using DFT gauge?? from the base metal or from the profile?? can you please explain on that?? Upto my knowledge it will be from the peak height.Please clarify.
 
regards,
 
Arun S Das
 


From: haseeb ph <haseebph@gmail.com>
To: materials-welding@googlegroups.com
Sent: Thu, 28 October, 2010 1:21:17 AM
Subject: Re: [MW:7883] Surface preparation and coating

to control the dft first you have to know the paint type, if it is a high build or not and most safe is first paint on the test panel and from that you can calculate no. of passes required to get the correct dft

Haseeb
KSA

On Wed, Oct 27, 2010 at 10:33 AM, Sundaram Sundaram <nss2410@gmail.com> wrote:
Thanku for your reply Mr.Gole.The primer DFT- 75microns,midcoat coat- 75 microns,final coat- 75 microns.overall 225 microns.Most of the times the total DFT is exceeding 225microns and how to control this.Can you give some more clear picture,pls


On Wed, Oct 27, 2010 at 11:15 AM, BHARAT GOLE <bharatgole@hotmail.com> wrote:
If surface profile is more than acceptable limit then it may cause for rust rashing i.e high peaks may expose after paint curing/contraction will be rusted.
Actaully it depend upon the so many factors such as whole paint syetem and DFT etc

Bharat B. Gole

 

 





> Date: Tue, 26 Oct 2010 22:58:41 -0700
> Subject: [MW:7857] Surface preparation and coating
> From: nss2410@gmail.com
> To: materials-welding@googlegroups.com

>
> Dear friends,
> Blasting Grade required - SA2.5
> Surface profile required - 40 - 70microns
>
> If the surface profile crossing the required limit 70-
> 80microns then what will the effect on painting and what is the
> reference code.Please guideme
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at http://materials-welding.blogspot.com/
> The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

[MW:34820] RE: 34813] Clarification in Rate of heating and cooling.

Hello,   Please see the response below.   Regards.   P. Goswami, P. Eng, IWE.   From: materials-welding@googlegroups.com <materials-weld...