Re: Re: [MW:7962] No of Welders

Dear Mr. Das,
First of all, my appologies for refering a wrong para of API1104. Read 6.1 for 621.
I don't think it mandatory to have 2 welders on pipes above 12", I couldn't find any thing to support this requirement in API 1104. Whereas in Section IX it is allowed to qualify more than one welder on a single test coupon. Refer QW-306.
It is not mandatory to use two welders in pipes larger than 12" in Section IX also.

Regards,
Dr. Paulose John
QA/QC Manager
Unisis Engineering
KSA

On Sun, 31 Oct 2010 08:08:06 +0530 Arun Das wrote
>

Dear Dr.John,

As a custom for above 12" pipe we will be using 2 welders for the welding process. It is so done because of heat input and distribution factors I beleive, but my question was that do this is stated as mandatory in any of the codes or standards.

I am having 1104 20 th edition of November 2005 with me. API 1104:2007. is the modifications??

Thanks and regards,
>

Arun S Das

From: Dr. Paulose John <drpaulosejohn@rediffmail.com>
>To: materials-welding <materials-welding@googlegroups.com>
>Sent: Sat, 30 October, 2010 4:07:56 PM
>Subject: Re: Re: [MW:7943] No of Welders
>
> Dear Mr. Arun,
>
>Minimum number of welders to be qualified by one WPS is - One welder. The welder who performs the PQR coupen welding is automatically becomes qualified. Please refer 2nd para of QW 301.2 of Section IX:2010 and para 621 of API 1104:2007.
>
>Regards,
>Dr. Paulose John
>QA/QC Manager,
>Unisis Engineering,
>Saudi Arabia
>.
>On Sat, 30 Oct 2010 14:15:07 , No ID Specified wrote
>

To my knowledge there is no limit for number of welder qualificationupon one WPS, You can qualify as many as per to the requirement for your project.

Here By,

P.BalajiRajan,

-------Original Message-------

From: Arun Das

Date: 10/28/10 17:39:52

To: materials-welding@googlegroups.com

Subject: [MW:7911] No of Welders

Sir,

Minimum number of welders to be qualified upon one WPS is mentioned in SEC 1X or API 1104.

We are using PIPE,16"X0.375"WT STD SCH API 5L X52

Thanksinadvance

with regards,
>

Arun S Das

FREE Animations for your email - by IncrediMail! Click Here!

--
>To post to this group, send email to materials-welding@googlegroups.com
>To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
>For more options, visit this group's bolg at http://materials-welding.blogspot.com/
>The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
>
>

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog