Skip to main content

Re: [MW:8964] WPQT P.No & F.No. Range

By Materials & Welding
we know that P num & F num are essential variables as per QW 403.18 & QW 404.15,
here if a welder is qualified with  any base metal (p1 to p11, p34, p41 to p 49) then he can weld (p1 to p11, p34, p41 to p 49)according to QW 423.1
& we know that if a welder qualified with an F no ( 34,41 to 46) then  he is qualified to weld with F no(34,41-46) according to qw 433.
so this welder can weld as u said

On Mon, Dec 27, 2010 at 2:57 PM, binoy soman <binoy.sadhupuram@gmail.com> wrote:
yes, welder is qualified to weld


On Wed, Dec 22, 2010 at 8:36 AM, praveen alavandar <praveenakds@yahoo.com> wrote:
Dear Limesh,
 
Absolutely yes for both your questions as per ASME Sec.IX 2010.
 
But you also need to look into the practical application when applying this wide range.
 
Regards,
 
Praveen Alavandar
Sr.Welding Engineer
Muscat
 


--- On Wed, 12/22/10, limesh M <limesh78@gmail.com> wrote:

From: limesh M <limesh78@gmail.com>
Subject: [MW:0] WPQT P.No & F.No. Range
To: "Materials & Welding" <materials-welding@googlegroups.com>
Date: Wednesday, December 22, 2010, 10:26 AM


Dear All,

Welding Code: ASME BPVC SEC IX, 2010 edition

 
A welder qualified on P No.45 material by using F No. 43 filler wire. I need clarification on following queries based on QW 423.1 and QW 433.
 
1. Is the welder qualified to weld P.No. 34, 41, 42, 43, 44, 45, 46, 47, 48 and 49 materials?
 

2. Is the welder qualified to use F.No. 34, 41, 42, 43, 44, 45 and 46 consumables?

 

 

Regards,

 

Limesh

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.


--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.


--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

[MW:5202] RE: 5200] NDT after PWHT

By Materials & Welding
------------------------------------- Interpretation:  I‑89‑14 Subject:         Section I (1986 Edition, 1987 Addenda), PW‑11,                  NDE Prior to PWHT Date Issued:     December 15, 1988 File:            BC88‑393   Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39?   Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation:  VIII-1-98-09 Subject:         Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE                 ...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more