Wednesday, December 29, 2010

RE: [MW:8976] Combination of PQR for WPS

Manpreet,
 
You cannot support combining these two PQR's to prepare a WPS having a wide range from 1.5mm to 30mm, you are deviating from the clause QW-200.4(b) of ASME Sec.IX.
see below.
 

"For GTAW, SMAW, GMAW, PAW, and SAW, or combinations of these processes, a PQR for a process recording a test coupon that was at least 12 in. (13 mm) thick may be combined with one or more other PQRs recording another welding process and any greater base metal thickness. In this case, the process recorded on the first PQR may be used to deposit the root layers using the process(es) recorded on that PQR up to 2t (for shortcircuiting type of GMAW, see QW-404.32) in thickness on base metal of the maximum thickness qualified by the other PQR(s) used to support the WPS. The requirements of Note (1) of tables QW-451.1 and QW-451.2 shall apply."

 

So you will have,

 

for PQR 1 : WPS range : 1.5mm to 12mm (Without impact) & 2.5mm to 12mm (With impact) assuming you dont do a PWHT above the upper transformation temperature.

 

For PQR 2: WPS range : 5mm to 30mm (Without impact) & 15mm to 30mm (With impact)

 

Regards,

 

Praveen



--- On Wed, 12/29/10, Bathula Raghuram (Mumbai - PIPING) <R.Bathula@ticb.com> wrote:

From: Bathula Raghuram (Mumbai - PIPING) <R.Bathula@ticb.com>
Subject: RE: [MW:8975] Combination of PQR for WPS
To: "materials-welding" <materials-welding@googlegroups.com>
Date: Wednesday, December 29, 2010, 12:57 PM

5-12mm w/o impact, else 6-12mm

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of manpreet
Sent: Wednesday, December 29, 2010 12:03 PM
To: materials-welding
Subject: [MW:8974] Combination of PQR for WPS

 

Dear All,

Procedure qualification as per ASME sec ix,

I have 2 PQR:-
                        *PQR 1-   GTaw-6mm thick 
                        *PQR 2-   Smaw- 15 mm thick

What would be the thickness renge for base and weld metal?

for combined WPS,  base metal thickness range shall be 1.5mm to 30mm, am i correct?

Regards
Manpreet Singh


--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

Re: [MW:34832] Inquiry about Single Bevel with Back Grinding

Dear Uday, As per your question that one is called with backing only,Simple both side you are welding it is backing with strip or without st...