Skip to main content

[MW:3318] RE: 3317] Base Metal

By Materials & Welding

Hello Norberto,

 

Normalised C – Mn steel.

Requirements reg charpy values can be till  @ -40 degr.

Welding with E 7018 or E7018-1 like

TENACITO R or SUPERCITO 7018S

http://www.alw-tool.com/WPC/oerlikon/MA/EN/index.php  

 

 

Met vriendelijke groet, with kind regards,

mit freundlichem Grüss, Salutations,

 

Ing. Erwin GERING, IWE

Product Manager Welding Consumables

 

 

Van: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] Namens Norberto Barbosa
Verzonden: vrijdag 25 september 2009 13:11
Aan: materials-welding@googlegroups.com
Onderwerp: [MW:3317] Base Metal

 

Hi, everybody
Is there someone who knows this kind of Base Material "S-355 J2 G3", regarding;
1)Similarity with ASTM;
2) Quimical Composition
3) and if possible an adequate electrode with its AWS classification and specification to weld this material.
I'll be glad.

Regardings,
Norberto de Souza Barbosa - Brazil
 



Novo Internet Explorer 8: mais rápido e muito mais seguro. Baixe agora, é grátis!

 


--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

[MW:5202] RE: 5200] NDT after PWHT

By Materials & Welding
------------------------------------- Interpretation:  I‑89‑14 Subject:         Section I (1986 Edition, 1987 Addenda), PW‑11,                  NDE Prior to PWHT Date Issued:     December 15, 1988 File:            BC88‑393   Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39?   Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation:  VIII-1-98-09 Subject:         Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE                 ...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more