If it is KSA and SAUDI ARAMCO project, then you have to go only with 9COM approved vendors, so check SA 9COM approved vendors list for procurement, if you are contractor check with PMT and if you are sub con check with your EPC, do not go any procurement without list because many previously approved vendors would have been blacklisted as of now for various reasons, so check as per that.
Vendors:
SANDVIK MATERIALS TECHNOLOGY AB SWEDEN
ULMA FORJA SPAIN
But again check with 9com latest.
Thanks.
Regards,
Mohamed Muneeb Mahaboob
CSWIP 3.2-89247/2 & AWS-CWI (2007)
ASNT-NDT-L2-RTFI-RT-UT-MT-PT.
SAP#:70021650 APs:JAPID, QCS & QCI.
Say (O Muhammad SAW to mankind). "If the sea were ink for (writing) the Words of my Lord, surely, the sea would be exhausted before the Words of my Lord would be finished, even if we brought (another sea) like it for its aid."18-109
From: Revdiwala DarshanDate: 2018-11-15 03:45Subject: Re: Re: [MW:28627] RE: 28480] Welding of UNS31254thank you for valuable information. can you suggest from where i can buy pipe for PQR Qualification. As all raw material for job will be supplied free issue by our client and it is not yet produced but before that i have to qualify new PQR. I am in KSA. Is there any reputed vendor who can provide SANDVIK 254 SMO.----Hi Darshan,
If this is UNS 31254 then definitely P8 G4 regardless of whatever outsourced it maybe and mostly comes with sandvik 254 SMO, simply we call it SMO material, for this you can use ENiCrMo-12 is suggested from Part C of Sec 2, we do not had combination but only GTAW as our thickness requirement was up to MAX 11.08.
SANICRO60 - No idea.
We used BM as SANDVIK 254 SMO with ENiCrMo-3 from ESAB.
Welding.
The heat input during welding should not exceed 1.5 kJ/mm, and in multi-pass welding the interpass temperature should not exceed 100°C (210°F). A stringer bead welding technique should be used.
The welding of fully austenitic steels usually entails a risk of hot-cracking in the weld metal, particularly if the weldment is under constraint. However, since Sandvik 254 SMO has a very high degree of purity, the risk of this type of cracking is greatly reduced. Backing bars or similar devices of copper alloys must not be used since copper penetration into the grain boundaries in stainless steel can lead to cracking.
So when you come to practical experience definitely do PT after the completion of each pass slow cooling done, cracks is possible after every pass, alert your inspectors and techinicinas to look for crack during their visual inspection regardless of welding parameters followed.
Regards,
M.Muneeb
Mr. muneeb,My material is out sources, welding consumable is SANICRO60 from sandvik.--On Sun, 28 Oct 2018, 10:28 am Mohamed Muneeb, <muneebslsa@gmail.com> wrote:Greetings,If I am not wrong your material is Sandvik smo which comes under p8 group 4? Please confirm.For this you can definitely use mentioned fillers as we did the same in gosps for crevice services.--On Sun, Oct 28, 2018, 2:13 PM Revdiwala Darshan <darshanmrevdiwala@gmail.com> wrote:Thankyou sir for your valuable reply.I am trying ESAB ERNiCrMo-3 for GTAW and ENiCrMo-3 for SMAW.--On Sat, 27 Oct 2018, 5:28 am PGoswami, <pgoswami@quickclic.net> wrote:Hi,
Please see the attached document providing detailed information on UNS 31254 steel, including welding. Recommended consumables are highlighted. Usually Inconel 625(ER-NiCrMo3) is the preferred grade for this alloy. The other grades are recommended based on the design criteria.
You should check with reputed manufacturers, on the best recommendation.
I had dealt with Metrode products in the past. However there're other good manufacturers also.
Thanks.
P.Goswami.P.Eng, IWE.
Welding & Metallurgical Specialist
-----Original Message-----
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Darshan Revdiwala
Sent: October 22, 2018 12:43 PM
To: Materials & Welding <materials-welding@googlegroups.com>
Subject: [MW:28480] Welding of UNS31254
Can anyone share practical experience for welding of UNS 31254 and consumables selection for Tig and SMAW process.
--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.
No comments:
Post a Comment