Skip to main content

[MW:31547] Re: Invitation for a Webinar - Topic : Welding of CSEF Gr 91 Steels - Practical Aspects

By Materials & Welding
please watch live @ https://www.youtube.com/watch?v=vrI4CB0xoiA  

On Monday, 5 October 2020 at 15:04:48 UTC+5:30 MW wrote:
From: IIW Mumbai [mailto:iiwm...@gmail.com]
Sent: 05 October 2020 14:53
Subject: Fwd: Subject: Invitation for a Webinar

  Dear All,
  The Indian Institute of Welding Mumbai Branch invites you for a Webinar On

    Topic : Welding of CSEF Gr 91 Steels - Practical Aspects
  Brief Introduction About Speaker:  Mr. Pradip Goswami has more than 37 years of experience in the Welding Field , he is a subject matter expert in Welding Engineering, Metallurgical Engineering , Material Selection & Corrosion Engineering. He will be diving deep into his practical knowledge about Welding CSEF Gr 91 Steels during this talk. Tune in to know more.
    Time :   Saturday-Oct 10, 2020 05:30 PM in India (GMT 12.00 noon)
 All are welcome. Attached flyer for more details and Registration Link. Please circulate to all your contacts.

  Best Regards
     sachin surve
THE INDIAN INSTITUTE OF WELDING
B-101, Hill View Apartment,
Opp. Western India Paper & Board Mills,
Opp.Raj Legacy, Surya Nagar
L. B. Shastri Marg, Vikhroli-400 083
Mumbai-Maharashtra
Tel: (022) 25772637 / 25794252



--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/d8f4fd2d-3635-40f2-8fcd-c8c33f6d897en%40googlegroups.com.

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more