Re: [MW:7012] RE: 6999] ASME SEC IX Code Issue

Dear All,

 

Thank you for the valuable inputs.The data which I have given is correct and your understanding of my querry also correct.Finally, I can write a WPS with a paper max interpass temperature of 195 C.

 

 

Material - LTCS (P1 Grouping according to ASME Sec IX)

Process - SMAW

PWHT - Yes (610+ - 10 C)

Weld Impact Tested - Yes 
Max interpass temperature recorded during PQR - 140 C

 

Dear All,

 

If I want to write a WPS with a maximum interpass temperature of 200 C, at what temperature range I have to do PWHT?

 

What is the upper transformation temperature of LTCS?

 

Upper critical temperature and upper transformation temperature are same or different?

 

If I am doing PWHT above upper transformation temperature what would happen?

 

 

 

 

Regards,

 

Limesh

 

 

On 9/14/10, GOSWAMI Pradip -THERMAL <pradip.goswami@opg.com> wrote:

Limesh,

 

PWHT is an essential variable as per Sec-IX. Please look under any table from QW-252 onwards.

 

If I understand correctly: You've :-Low temperature carbon steel impact tested PQR with a PWHT range of 600⁰±10⁰C.

 

·         This PQR  will  support a WPS with PWHT only. It will not support  a WPS without PWHT.

 

Regarding the  max interpass clause QW-406.3, An increase of more than 100°F (55°C) in the maximum interpass temperature recorded on the PQR is considered to be a supplemental essential variable. This does not apply if the PWHT is for C.S is above upper transformation temperature (723⁰C) or for austenitic S.S , when soln annealed.

 

As the PWHT in your case  is 600⁰±10⁰C. the  max interpass temperature clause as above will apply, second clause as above will not apply.

 

To summarize based on the PQR data(max interpass 140⁰C), on paper max interpass allowed would be 195⁰C ( when there's impact requirement), welds shall be subject to PWHT. If you want to refer this PQR for case where PWHT is to be performed but No impact Requirement, you may increase interpass temperature to 200⁰C.

 

 

Hope it clarifies your query.

 

Thanks.

 

Pradip Goswami,P.Eng.

Welding & Metallurgical Engineer/Specialist

Ontario Power Generation Inc.

Email-pgoswami@sympatico.ca,

pgoswami@quickclic.net

---

 

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of limesh M
Sent: Tuesday, September 14, 2010 8:43 AM
To: materials-welding@googlegroups.com
Subject: [MW:6999] ASME SEC IX Code Issue

 

Dear All,

Design Code: ASME B31.3     Welding Code: ASME SEC IX

I have a Low temperature carbon steel impact tested PQR with a PWHT range of 600⁰±10⁰C.Is this condition giving an exemption for me on QW406.3 to prepare a WPS with maximum interpass temperature of 200⁰C.

Maximum interpass temperature observed during specimen welding: 140⁰C

 

Regards,

 

Limesh

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

---

THIS MESSAGE IS ONLY INTENDED FOR THE USE OF THE INTENDED RECIPIENT(S) AND MAY CONTAIN INFORMATION THAT IS PRIVILEGED, PROPRIETARY AND/OR CONFIDENTIAL. If you are not the intended recipient, you are hereby notified that any review, retransmission, dissemination, distribution, copying, conversion to hard copy or other use of this communication is strictly prohibited. If you are not the intended recipient and have received this message in error, please notify me by return e-mail and delete this message from your system. Ontario Power Generation Inc.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.