Re: [MW:35238] Overlay welding defects

Dear sir,

Thank you for your feedback sir.

We use LPG Cylinder for Preheat dia above 1000mm,We use Furnace for Small sizes.

Argon Gas Used Praxair ( Linde).

The below points,We will check in the Process.

If you are using the GMAW process, make sure to keep a lower stick out and the correct amount of shielding 

gas flow rate. A very low/high gas flow rate or welding without a flow meter may also induce porosity. 

Make sure not to open the Argon cylinder fully, as it may increase gas flow velocity and may induce pinholes.

Mainly the defect is noticed in the Bore bottom Radius Area ,Second one Continuous dotted line in the Overlapping.

Regards,

R.Gowtham.

On Mon, Sep 9, 2024 at 5:44 PM sridhar cn <sridharcn305@gmail.com> wrote:

Mr. Gowtham,

These sorts of problems are common in overly welding. 

Please make sure that jobs are preheated properly (not with Oxy-fuel gas; it may create pinholes) 

using LPG, according to your WPS.

Make sure that the Argon gas is procured from a reputed brand and not from a local manufacturer

as it may not be pure even though certified for a 99.99% purity level.

The overlay should not be done in an open area where air circulation is more and should be well-protected 

from fan breeze, etc.

If required, use UHP Argon (99.999% pure), but it will be very costly.

GTAW and plasma arc welding could be more appropriate for the overlay technique.

If you are using the GMAW process, make sure to keep a lower stick out and the correct amount of shielding 

gas flow rate. A very low/high gas flow rate or welding without a flow meter may also induce porosity. 

Make sure not to open the Argon cylinder fully, as it may increase gas flow velocity and may induce pinholes.

Hope the above information will be of help to you.

C Sridhar.

--------------------------------------------------------------------------------------------------------

properly according to your WPS.

On Mon, 9 Sept 2024 at 10:57, Karthick Flow Controls <kfccovaigm@gmail.com> wrote:

Dear sir,

Welding Valve body & Adapter,(Ball Valve,Triple offset Butterfly,Trunnion mounted Ball Valve & Top Entry Ball Valve.

Regards,

R.Gowtham.

On Fri, Sep 6, 2024 at 11:21 AM Mohd Siraj <mohd52100@gmail.com> wrote:

WCB/LCB fitting elbow or tee components, pl follow,

weld with CS filler wire first then start overlay.

On Thursday, September 5, 2024 at 11:07:20 AM UTC+3 Karthick Flow Controls wrote:

Inconel 625 & 316L -GMAW

Shielding Gas - Argon 

Position -1G

Regards,

R.Gowtham.

On Wed, Sep 4, 2024 at 4:08 PM 'J Prinsen' via Materials & Welding <material...@googlegroups.com> wrote:

First questions: which process, which shielding gas, which welding position, which welding parameters

Regards

Jurgen Prinsen IWE

Weld-Tech BV

Welding Engineering and Consultancy

---

Van: "Karthick Flow Controls" <kfcco...@gmail.com>
Aan: "Materials & Welding" <material...@googlegroups.com>
Verzonden: Woensdag 4 september 2024 07:26:39
Onderwerp: [MW:35217] Overlay welding defects

Dear Experts,

Welding Overlay, After Machining the Pin holes and blow holes noticed in Overlapping Joint area, After attend the defects, It will open some other places, The defects noticed Uniform inline.   ( Overlay Material ,316L ,Inconel 625 ,St6 & ST21,Base Material WCB/LCB),

How to prevent the defects?

Regards,

R.Gowtham.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/33a4e532-e9d1-45f0-a35f-2172b2263b12n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-weld...@googlegroups.com.

To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/1591554008.13124552.1725439862211.JavaMail.zimbra%40online.nl.

--

Thanks & Regards,

R.GOWTHAM.

KARTHICK FLOW CONTROLS, 

1/575 SNMV College Road, 

Mallumichampatti,

Coimbatore - 641 050.

Website: http://www.karthickflow.com

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/287ab92f-439c-461a-9c0d-6a9c21ca53abn%40googlegroups.com.

--

Thanks & Regards,

R.GOWTHAM.

KARTHICK FLOW CONTROLS, 

1/575 SNMV College Road, 

Mallumichampatti,

Coimbatore - 641 050.

Website: http://www.karthickflow.com

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CADsiqoGENtjXWAmz5FGB0JFFwQN0GAQ%3Dk9385JFQ-J7cn920tg%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHo%3DYigTK9QZO4qm5sp4r%2BsamNy1LJ8baGBkepB5RB4qJcR%2Bug%40mail.gmail.com.

--

Thanks & Regards,

R.GOWTHAM.

KARTHICK FLOW CONTROLS, 

1/575 SNMV College Road, 

Mallumichampatti,

Coimbatore - 641 050.

Website: http://www.karthickflow.com

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CADsiqoF07SUcjCNiusS67UtZfecZYtn4VxbPKYsH7RHgpmt0dg%40mail.gmail.com.