Skip to main content

[MW:14315] Re: 14305] ENiCrMo6 - AC operating

By Materials & Welding
please allow me to answer your questions.
1, YES. Just do it.
2, T=Tungsten, (W) . This element should be W, Maybe our company print it wrong, I will inform them to correct it.
 
Roy
 
 
 
Sent: Friday, May 18, 2012 8:55 PM
Subject: Re: [MW:14305] ENiCrMo6 - AC operating
 
Thanks Mr.Saroj,
 
Please clarify the following points.
 
1) Are these mechanical values indicated in the catalogue can be chieved after welding with AC current of 150 to 170 Amps for 4mm electrode?
 
2) What is the "T" alloying element mentioned?
 
Regards,
 
Srinivasan

On Fri, May 18, 2012 at 11:05 AM, saroj kumar <sarojselva@gmail.com> wrote:
Dear Srinivasan,
 
Yes, the SMAW electrode ENiCrMo-6 is available for welding 9% Nickel steel base material for
Low temp application with AC.
 
You can go for BOHLER brand FOX NIBAS 60/15, which is highly suitable. The catalogue is attached
herewith for your perusal.


Thanks/Best Regards,
 
M.Saroj Kumar
Chennai,India.
 
On Wed, May 16, 2012 at 4:58 PM, Srinivasan Jagannathan <jsrisud@gmail.com> wrote:
Dear Experts,
 
We have a job to be welded with ENiCrMo6 which operates on DC.
 
We need to weld with AC current due to Arc Blow / Magnetism.
 
Is it possible to have SMAW electrode of same specification, operating on AC without compromising Mechanical Properties?
 
Please advice.
 
Regards,
 
Srinivasan
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to mailto:materials-welding%2Bunsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
 
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to mailto:materials-welding%2Bunsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.


 
--
J.SRINIVASAN

GENERAL MANAGER - TRAINING

D&H SECHERON - INDORE

Mob: 7898989756

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

[MW:30043] Weep hole

By Materials & Welding
If weep hole is not provided in dummy pipe before welding What will happen??? -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/da251ee6-fa7f-4851-b876-cdb3834ae341%40googlegroups.com .
Post a Comment
Read more

[MW:36169] Cold Bending Qualification

By Materials & Welding
Dear Experts,  Can anyone share the inspection requirements or a qualification procedure for cold bending? Our client spec states only the requirements for induction bending and would like to know your opinion on the cold bend inspection requirements. The code of construction is B31.3, Max. 5D bends, A106 SS 316L.  Thanks in Advance. -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion visit https://groups.google.com/d/msgid/materials-welding/1be61cc3-e9c9-4a5f-834d-e8485e248432n%40googlegroups.com .
Post a Comment
Read more