Skip to main content

[MW:6740] Comparison between CP189 and SNT-TC-1A 2006 edition

By Materials & Welding

for info..

-----Original Message-----

From: PEMMARAJU RAGHAVENDRA [mailto:rpe@hzw.ltindia.com]

Sent: Friday, August 27, 2010 10:30 AM

To: Bathula Raghuram (Mumbai - PIPING)

Subject: Re: FW:

Thanks Raghuram.

I have prepared a comparison sheet as per attachment.

FYI

Regards,


>>> "Bathula Raghuram (Mumbai - PIPING)" <R.Bathula@ticb.com> 27/08/2010
>>> 08:59 am >>>


Bill Plumstead Jr.<http://www.linkedin.com/groups?viewMemberFeed=&gid=122787&memberID=46511406&goback=%2Egmp_122787>

* CP-189 is a STANDARD and SNT-TC-1A is a RECOMMENDED PRACTICE. CP-189 has requirements that must be met whereas SNT-TC-1A recommendations can be modified to met the needs of the employer. A couple of key points for comparison:
- SNT-TC-1A has 3 levels of qualification (Level I, Level II, Level III)
- CP-189 has 6 levels of qualification (Trainee, Level I, Level II, Level II Limited, Level III, NDT Instructor)
- CP-189 requires the Level III to hold a current ASNT certificate in the method
- CP-189 requires training of Level I and Level II personnel by a qualified NDT Instructor


________________________________________
From: PEMMARAJU RAGHAVENDRA [rpe@hzw.ltindia.com]
Sent: Saturday, August 21, 2010 1:05 PM
To: Bathula Raghuram (Mumbai - PIPING)
Subject: Comparison between CP189 and SNT-TC-1A 2006 edition

Do you have the comparison between above two documents of ASNT,.

Regards,

Larsen & Toubro Limited
www.larsentoubro.com



Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more