Skip to main content

RE: 26717] Re: SA 516 Gr70 + SS 410S roll bonded clad plate

By Materials & Welding

Hi Prem,

 

I could not convey the right response to your query posted In the WhatsApp forum.

 

1.       Clad Plates are most commonly manufactured by roll-bonding for conventional alloys like martensitic stainless , austenitic stainless steel clad plates.

2.       Due to the manufacturing technique the dilution of clad by the substrate (i.e. here C.S) are minimal

3.       Hence issue of undiluted chemistry on the clad plates (as received from the mill) is never a concern.

 

This issue may be a concern during clad restoration of L& C-Seams. A judicious selection of welding techniques +No of passes would definitely assure the above. API RP-582 recommends this technique(as below) for clad restoration of 410/410S.

 

The other alternative would be ,

1.       barrier layer(start typically 1 -2mm below the interface) by 309L, 1/8" dia

2.       2nd & 3rd layer , by  AWS E410-16, 1/8" dia

3.       4TH  layer, optional , by  AWS E410-16, 1/8"(3.15 mm) or 5/32"(4.0 mm) dia.

 

Hope this would help.

 

Thanks.

 

 

P.Goswami.P.Eng, IWE.

Welding & Metallurgical Specialist

 

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of MW
Sent: August 14, 2017 10:53 PM
To: Materials & Welding <materials-welding@googlegroups.com>
Subject: [MW:26717] Re: SA 516 Gr70 + SS 410S roll bonded clad plate

 

what is your clad thickness?

On Tuesday, 15 August 2017 06:51:37 UTC+4, PREM SHANKARDUTT NAUTIYAL wrote:

Dear Friends

A column is going to be fabricated as per ASME Sec VIII Div.1

The shell plate material is SA 516Gr.70 (14mm thk) + SS 410S (3.5 mm thk) Roll Bonded clad plate.

Client spec. mentions undiluted chemistry of SS 410S at height of 3mm for the roll bonded clad plate.

My doubt is whether plate manufacturer can achieve this stringent requirement ?

PREM S NAUTIYAL
CELL : 9769316004

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.



AVG logo

This email has been checked for viruses by AVG antivirus software.
www.avg.com


Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more