Re: [MW:9908] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW

Dear Abhay,

After Welding, Impact testing shall be carried out at Weld and Haz (FL, FL+2) of both side materials, ASME sec viii, UG-84 states Impact locations, Please let me know if you need further clarification.

Regards
Manpreet Singh



On Wed, 16 Feb 2011 10:58:11 , "Abhonkar, Abhay \(NAR\)" <AAbhonkar@Dresser-Rand.com> wrote

Dear Sirs,

Pl guide me on below.

Have completed the WPS / PQR for low temp piping (SA333 Gr 6) by using SMAW and the electrodes is E 7018-1.

 

My low temp pipe is already impact tested and my electrodes also qualify for impact testing.

 

Now after welding, for impact test, whether I have to carry the impact test at all places i.e. for pipes, for welding location and at HAZ area.

OR I have to carry at HAZ area only as my pipe and electrodes are already impact tested.

 

Also request you to advise the ASME section for the above.

 

Regards,

Abhay

Ext 448

 

IMPORTANT NOTICE:
This email may be confidential, may be legally privileged, and is for the intended recipient only. Unauthorized access, disclosure, copying, distribution, or reliance on any of it by anyone else is prohibited and may be a criminal offense. Please delete if obtained in error and email confirmation to the sender.

---

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Krandrk
Sent: Monday, February 14, 2011 3:56 PM
To: materials-welding@googlegroups.com
Subject: Re: [MW:9873] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW

 

Dear Mr.Abhay,

    i hope you got idea about the filler wire and electrode, but as you said you are going to use 2" Sch 80 for WPS and PQR. before finalish that make sure what is your actual job (thickness and diameter range), and also make sure you may have PWHT requirement or not. so that you can make WPS/PQR to cover all your requirements. also 2' pipe will not cover to do all mechanical testing. so also make sure howmany specimans you requrired to all mechanical testing including impact.

 

with regards,

R.Kumar

On Mon, Feb 14, 2011 at 8:15 AM, praveen alavandar <praveenakds@yahoo.com> wrote:

Dear Abhay,   You can also try ER 70S6, this filler wire has got good amount of Mn for better low temp. toughness and most of the time impact tested at -50 Deg.C, you need to ask your supplier for specific batch where it has been impact tested to -50 Deg.C.   ER 80SNi1 will give you guranteed values, but if your service is sour you need to make sure that the maximum Ni content doesnt exceed 1.0%.   More over, It is recommended you use a full GTAW for welding 2" x 5.54mm pipe instead of combination process (GTAW + SMAW) and most international client specs. recommeds the same.   Regards,   Praveen --- On Mon, 2/14/11, james gerald <gerry_tup@yahoo.com> wrote: From: james gerald <gerry_tup@yahoo.com> Subject: RE: [MW:9864] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW To: materials-welding@googlegroups.com Date: Monday, February 14, 2011, 11:08 AM   Abhay,   It depends on your MDMT(Minimum Design Metal Temperature). I suppose ER70S-2 is suitable for use only upto MDMT of -30degC.   These details can be obtained from ASME Sec.IIC   SFA 5.18 for ER70S2  & SFA 5.28 for ER 80SNi-1   Check the above sections in ASME Sec.IIC   J.GERALD JAYAKUMAR 00919344954677   --- On Mon, 2/14/11, Abhonkar, Abhay (NAR) <AAbhonkar@Dresser-Rand.com> wrote: From: Abhonkar, Abhay (NAR) <AAbhonkar@Dresser-Rand.com> Subject: RE: [MW:9863] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW To: materials-welding@googlegroups.com Date: Monday, February 14, 2011, 5:28 AM Dear Sir, Many thanks for your information. For SMAW, have selected the same but for GTAW we are using ER 70S2. Is it right? Also request you to inform from where I can select the same, as have gone through the ASME sec 2 Part c but not able to succeed.   Thanks.   Regards, Abhay Ext 448 M +91 9898031162   IMPORTANT NOTICE: This email may be confidential, may be legally privileged, and is for the intended recipient only. Unauthorized access, disclosure, copying, distribution, or reliance on any of it by anyone else is prohibited and may be a criminal offense. Please delete if obtained in error and email confirmation to the sender. From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of james gerald Sent: Monday, February 14, 2011 10:47 AM To: materials-welding@googlegroups.com Subject: Re: [MW:9861] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW   GTAW - ER80SNi1 SMAW - E7018-1   The above can be used to weld A333 Gr.6 Pipe upto MDMT of -45degC J.GERALD JAYAKUMAR 00919344954677   --- On Mon, 2/14/11, Abhonkar, Abhay (NAR) <AAbhonkar@Dresser-Rand.com> wrote: From: Abhonkar, Abhay (NAR) <AAbhonkar@Dresser-Rand.com> Subject: [MW:9855] electrode selection of WPS of SA 333 Gr 6 low temp piping, GTAW +SMAW To: materials-welding@googlegroups.com Date: Monday, February 14, 2011, 3:57 AM Dear Sirs, Pl advise how can select the electrodes for SA 333 Gr 6 (P1 and G1) low temp pipe. I want to prepare WPS / PQR and then also WPQ for our current project. Have selected the thickness around 5.55 mm (2 "S 80 pipe) for preparing WPS.   We followed the process of root run by GTAW and then by SMAW.   Regards, Abhay Ext 448   IMPORTANT NOTICE: This email may be confidential, may be legally privileged, and is for the intended recipient only. Unauthorized access, disclosure, copying, distribution, or reliance on any of it by anyone else is prohibited and may be a criminal offense. Please delete if obtained in error and email confirmation to the sender. -- To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.   -- To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents. -- To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

 

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

 

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.