Skip to main content

Re: [MW:7340] Re: Using WPS qualified as per D1.1 to weld pipework as per ASME IX

By Materials & Welding
Dear Philip,

As per understanding, if your going to use the WPS for the pipe work meant
for structural works or loading , you can adopt the WPS prepared as per
ASME.

If not, then you need run separate qualification as per ASME Sec IX

Regards,

K.Babu


----- Original Message -----
From: "israr" <ahmedisrar.nm@gmail.com>
To: "Materials & Welding" <materials-welding@googlegroups.com>
Sent: Monday, October 04, 2010 12:16 AM
Subject: [MW:7334] Re: Using WPS qualified as per D1.1 to weld pipework as
per ASME IX


Hello Mr. Philip,

You can ask your lab to certify the test as per ASME Sec IX and AWS
D1.1 and you can prepare separate WPS as per Sec IX and D1.1 and use
the same test to prepare PQR then you can use the qualified WPS as per
ASME and AWS D1.1.

I have done the same while i was there in Dubai and same was accepted
by ABSG.

On Sep 28, 5:00 pm, "Philip, Taiye (Lagos)"
<Taiye.Phi...@deltaafrik.com> wrote:
> Hello gents,
>
> I have a WPS qualified as per D1.1 - 8 inches for welding structural
> work, in 6G position,
>
> My query is can I use these procedure to weld pipe work as per ASME IX
> for the same material?
>
> Pls I need further clarification with codes support.
>
> Regards
>
> Philip Taiye
>
> *** WORLEYPARSONS GROUP NOTICE ***
> "This email is confidential. If you are not the intended recipient, you
> must not disclose or use the information contained in it.
> If you have received this email in error, please notify us immediately by
> return email and delete the email and any attachments.
> Any personal views or opinions expressed by the writer may not
> necessarily reflect the views or opinions of any company in the
> WorleyParsons Group of Companies."

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to
materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at
http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and
meant for educational purposes only, Users must take their own decisions
w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more