Ref Sec IX: Let the first one finish 11 mm root and hp (+ some fill if the welding sequence says so) on full joint and then the other finishes off with remaining welding...Then you take care of some reinforcement in cap, too. This way, you fulfill the condition of "t".
Rgds,
Shashank Vagal
--- On Tue, 9/11/10, Sundaram Elumalai <Elumalai.Sundaram@starfab.com.sa> wrote:
From: Sundaram Elumalai <Elumalai.Sundaram@starfab.com.sa>
Subject: RE: [MW:8156] weld thicness
To: materials-welding@googlegroups.com
Date: Tuesday, 9 November, 2010, 12:52 PM
But, maximum they can deposit 12mm on the particular joint. With kind regards, Malai. 
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of george.dilintas@gr.bureauveritas.com
Sent: Monday, November 08, 2010 10:38 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:8135] weld thicness Yes if the other essential performance qualification parameters (process, F no, P No etc) are not altered
Dr. G. Dilintas - Authorized Inspector Supervisor
I&F Regional Technical Manager
Bureau Veritas Piraeus - Greece
Tel: +30 210 40 63 113/4
Fax: +30 210 40 63 118
Cell: +30 69 44 64 62 04
 Ahmed Husain <ahmraha@yahoo.com>
| Ahmed Husain <ahmraha@yahoo.com>
Sent by: materials-welding@googlegroups.com 07/11/2010 12:38 | Please respond to
materials-welding@googlegroups.com |
| | 
To | 
materials-welding@googlegroups.com | |
cc |
| |
Subject |
[MW:8122] weld thicness | |
Ref |
|
|
Dear All,
I need your valuable information/comment on following case.
There is a situation where 2 welders are qualified to weld 12mm thick. Ifthe job thickness is 20 mm and dia, say is 36", contractor divide the joint in half. First simultaneously, each will weld approx 10mm thick including root half the circum, as they are qualified in 12 mm only. Then the interchange their location and they will complete the remaining welding. Basically these 2 welders who are qualified upto 12 mm are welding 20mm thickness joint, but at any given location they are welding 10mm thickness.
Is this practice is acceptable.
Regards, Ahmed H. --
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents. -- To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents. -- To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
|
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at
http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
No comments:
Post a Comment