Skip to main content

Re: [MW:33219] Back welding process

Hi

For the inside welding requirements What is the specification or client requirements, weld joint efficiency considered during design, working pressure to design pressure (factor of safety) etc parameters will decide. 

If inside complete penetration, complete edges fusion happened no need to go for the inside seal run or capping else you can plan for the defect removal and can do the welding 

Coming to process, it should be as per approved WPS. 
SMAW would be acceptable with same consumables 

On Sun, 10 Jul 2022 at 10:27 AM, Mahesh Koppisetty <maheshmechanical24@gmail.com> wrote:
Respected experts ,
Happy Sunday to all. 

  A  48 " tubular having 25 mm thickness we made a single bevel butt joint. 

The root & Hotpass  is welded with GTAW and fill up and capping is welded with SMAW. 
My query is that, 

Is back welding  is required or not . If required , please tell the procedure of back welding.
I mean to ask ,
1. which welding process should I use GTAW or SMAW for back welding. ? 
2 . With back gouging or without  back gouging. ? 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CANDtUcF-8SZ%2BFOoa-TAaFqRO67EKXWL0bB-sjAb_SzhAuMRTpQ%40mail.gmail.com.
--
Thanks & Regards,
Lakshman kumar B
+91 9440031459.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAO-dY%3DjyzFdBR102r%2Btw9GT-3zZX%3DF_zgXGUYmQMS%2BHSn9w_8g%40mail.gmail.com.

Comments

Popular posts from this blog

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

[MW:36169] Cold Bending Qualification

Dear Experts,  Can anyone share the inspection requirements or a qualification procedure for cold bending? Our client spec states only the requirements for induction bending and would like to know your opinion on the cold bend inspection requirements. The code of construction is B31.3, Max. 5D bends, A106 SS 316L.  Thanks in Advance. -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion visit https://groups.google.com/d/msgid/materials-welding/1be61cc3-e9c9-4a5f-834d-e8485e248432n%40googlegroups.com .

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...