Skip to main content

[MW:23350] National Welding Seminar (NWS - 2015) - Call for Technical Papers

By Materials & Welding
Greetings from The Indian Institute Of Welding.
 
We are sure you must be aware about the National Welding Seminar (NWS - 2015) and concurrent WELD INDIA EXHIBITION going to be held in Vashi, Navi Mumbai, India in the state of the Art CIDCO Exhibition Centre, from 9th to 12th December, 2015.
 

Call for Technical Papers 
We invite welding professionals, scientists, researchers and academicians to present technical papers on the theme-related subjects at this seminar.

Topics Covered

• Welding Metallurgy and Weldability Analysis of Ferrous &
Non-Ferrous Materials
• Welding Systems and Equipment
• Welding Automation and Robotics
• Advanced Welding and Cutting Processes
• Welding Consumables and Procedures for New Materials
• Design & Manufacture of Welded Structures
• Inspection, Testing, Quality Control & Quality Assurance
• Computer Aided Welding Engineering
• Mathematical Modelling and Simulation in Welding
• Properties of Welded Joints
• Residual Stresses and Distortion
• Repair and Maintenance Welding
• Residual Life Estimation & Surface Engineering
• Human Resource Development in Welding
• Safety, Cost and Economics of Welding
• Application of Welding - Case Histories


We request the good personal support from you by registering as Delegate for the NWS and participating in the Exhibition and papers for the seminar.  

This is an  International Event wherein we expect active participation of International foreign delegates as well and only together we can make this event successful.
 
Thanking You,

THE INDIAN INSTITUTE OF WELDING,
MUMBAI BRANCH
B-101, Hill View Apartment,
Opp. Western India Paper & Board Mills,
L. B. Shastri Marg, Vikhroli-400 083, Mumbai.

--
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To post to this group, send email to materials-welding@googlegroups.com.
Visit this group at http://groups.google.com/group/materials-welding.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/59408b1a-0f2a-4083-a2e7-3ba2e4b46975%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more