Re: [MW:19677] IMPACT TEST IN PTC AT -47 DEG

what is consumable classicification?

On Fri, Dec 20, 2013 at 10:19 AM, Darapu Dattatreya <darapu_dattatreya@yahoo.com> wrote:

Dear Expert,

 

Please find attached Heat treatment procedure as requested by you.

 

 

Regards,

 

D.Dattatreya.

On Wednesday, December 18, 2013 1:48 PM, "george.dilintas@gr.bureauveritas.com" <george.dilintas@gr.bureauveritas.com> wrote:

could you send your normalizing procedure?

best regards

Dr. Georgios Dilintas

Authorized Nuclear Inspector
Authorized Inspector Supervisor
API 510 Inspector

I&F REGIONAL TECHNICAL MANAGER
BUREAU VERITAS HELLAS

Tel: +30 210 40 63 113/4
Fax: +30 210 40 63 118
Cell: +30 69 44 64 62 04
(See attached file: Dilintas_George.vcf)
Darapu Dattatreya ---18/12/2013 06:43:09---Dear Experts,  

From: Darapu Dattatreya <darapu_dattatreya@yahoo.com>
To: "materials-welding@googlegroups.com" <materials-welding@googlegroups.com>
Date: 18/12/2013 06:43
Subject: Re: [MW:19645] IMPACT TEST IN PTC AT -47 DEG
Sent by: materials-welding@googlegroups.com

Dear Experts,
 
We are facing Impact Test failures problem after Normalizing the pipe fittings manufactured Impact Tested SA 5416 Gr. 70 Material at - 46 deg. C
 
We have put a lot of pipe fittings in our normalizing furnace 25 mm thk. & 14 thk pipe fittings, after that we have selected one sample each thk and Impact tested, the 14 mm thk fitting the passing the Impact test requirement for parent metal, HAZ & Weld as per ASME B 31.3 & the other sample 25 mm thk. failing the Impact requirement on Parent metal & HAZ and the Impact value we have observed 8 , 10 & 12 etc. and the
 
Can any body explain the reason for the failures in Impact test requirements as per ASME B 31.1.
 
Regards,
 
D.Dattatreya.    


On Tuesday, December 20, 2011 10:16 PM, Dindo <dindodelacruz@gmail.com> wrote:
you have to monitor the actual welding of the coupon and make sure that you are within the parameters of the qualified WPS, if it still fails you can always send the coupon for stress relieving (which is more costly since you have to PWHT your vessel too)

On Mon, Dec 19, 2011 at 10:27 PM, Vivek Pandey <vivek.pande06@gmail.com> wrote:DEAR EXPERTS

AT this time Iam facing a critcal problem in impact test at minus 47
deg. I have a already existing qualified PQR WITH E 8018G & IMPACT
Tested at -47deg. I have used the same PQR in  vessel production test
at -47deg but this PTC has failed in imapct test of WELD & HAZ at
-47deg we are getting erratic value 10, 12, 90 in weld & 60, 10, 50 in
HAZ

Kindly suggest your opanion  about this problem as soon as possible

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to mailto:materials-welding%2Bunsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm

The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

This message contains confidential information. To know more, please click on the following link: http://disclaimer.bureauveritas.com

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.

For more options, visit

https://groups.google.com/groups/opt_out

.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.