[MW:19661] Re: 19659] ASTM 815 grade S31803 chemical comosition

Dear Colleagues,

i got a reply for my issue for your information,When there is an ellipsis (...), that means there is no requirement. The sample can have any concentration and it does not cause a non conformance.

On Fri, Dec 20, 2013 at 2:45 PM, Ezat Adel <ezatadel2008@gmail.com> wrote:

Dear Udit Maheshwari,

check the attached extract page from A815 document which stated that the fitting material shall conform to the chemical requirement in table 1 

for your advice 

On Fri, Dec 20, 2013 at 2:44 PM, Ezat Adel <ezatadel2008@gmail.com> wrote:

---------- Forwarded message ----------
From: Udit Maheshwari <udit.maheshwari@eil.co.in>
Date: Fri, Dec 20, 2013 at 10:21 AM
Subject: RE: 19659] ASTM 815 grade S31803 chemical comosition
To: Ezat Adel <ezatadel2008@gmail.com>

Dear Sir

 

You can check table 3 , if tolerances are under limit you can accept it

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Ezat Adel
Sent: Friday, December 20, 2013 12:16 PM
To: materials-welding
Subject: [MW:19659] ASTM 815 grade S31803 chemical comosition

 

Dear colleagues,

 

could you please check attached for ASTM 815 grade S31803 and advice me

what does the ellipsis(....) indicate to ,it means there is no CU% ,TI% content it means 0% content or it means it is not specified.

 

my issue i have a MTC which contain some of Ti%,Cu%,AL% and V% content

if this new product considered accept or not.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

---

MAIL HAS BEEN SCANNED BY MCAFEE e-APPLIANCE

---

The Mail has been scanned by Mcafee Appliance ********************************SAVE A TREE!***************************************** Please print only when necessary; avoid unnecessary prints and save the environment.

********************************DISCLAIMER*******************************************
"The contents of this E-mail (including the contents of the enclosure/(s) or attachment/(s) if any ) are privileged and confidential material of ENGINEERS INDIA LIMITED (EIL) and should not be disclosed to, used by or copied in any manner by anyone other than the intended addressee/(s). If this E-mail (including the enclosure/(s) or attachment/(s) if any ) has been received in error, please advise the sender immediately and delete it from your system. The views expressed in this E-mail message (including the enclosure/(s) or attachment/(s) if any) are those of the individual sender, except where the sender expressly, and with necessary authority, states them to be the views of EIL."

Dear Udit Maheshwari,

check the attached extract page from A815 document which stated that the fitting material shall conform to the chemical requirement in table 1 

for your advice 

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.