Skip to main content

[MW:3853] RE: 3851] Visual Examination of the welds

By Materials & Welding
Dear Friend
 
Your Answer Is ISO5817

From: Nachhattar Singh
Sent: Sun 2009/12/20 09:04 AM
To: materials-welding@googlegroups.com
Cc: 'PEMMARAJU RAGHAVENDRA'
Subject: [MW:3851] Visual Examination of the welds

Dear Members  I would like to request the copy of the code or the part which can elaborate the recognition of the weld seams for acceptance / rejection during the visual examination of the weld  This request is because some of the clients would want the welds to have the grinding done so that the peaks can be reduced / merged , but some say that no you should leave them in as is condition since the grinding reduces the strength of the weld overlays  For this purpose - Preferably some sketches or some photographs will help ,  so that they can be used as a guide for acceptance of the welding .  Thanks and bets regards   -------------------------------------------------------------------------- Nachhattar Singh Director Phone: 91-22-2758 0044 - 91-98201 81158 Fax:91-22-27580033 Email:n.singh@moodyint.com Web: http://www.moodyint.com/ Web: http://www.edn.com.au/ Moody International (I) Pvt Ltd 32 / 33 Gautam Complex , Sector - 11 C.B.D Belapur , Navi Mumbai - 400 614 Maharashtra (India) Mumbai Maharashtra 400 614 India RSTS & EDN are wholly owned subsidiaries of Moody International and are leaders in HSE Consulting and Training    Moody Group Confidentiality Note: The information transmitted is intended only for the person(s) or entity to which it is addressed. It may contain confidential and/or privileged information or material. Any review, retransmission, dissemination to other use of, or taking of any action in reliance upon this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer.  __________      --  To post to this group, send email to materials-welding@googlegroups.com To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com For more options, visit this group's bolg at http://materials-welding.blogspot.com/ The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more