[MW:1227] RE: 1224] RE: 1220] Re: usage of phased array probes in TOFD

Dear Raghvendra,

May be correction required in your question. Using PA probes along with TOFD probes (simultaneously both method on one joint) - If that is the case Answer is yes.

FYI : TOFD probes are having normal connectors (lemo) where PA probes are coming with the multi point connector (to take care of each crystal energizing)

I hope your doubt might have cleared.

Regards.

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Rohit Bafna
Sent: Isnin, 20 Okt 08 05:00 pm
To: materials-welding@googlegroups.com
Cc: 'RAGHAVENDRA PEMMARAJU'
Subject: [MW:1224] RE: 1220] Re: usage of phased array probes in TOFD

Dear all,

How on earth can you do ToFD by attaching Phased Array probes. Totally not possible. These are two different techniques. I agree with SSK.

Regards,

Rohit Bafna

Director - Global Sales

------------------------------------------

TCR Engineering Services (India)
TCR Arabia (KSA), TCR Kuwait

TCR World Inc. (USA)

USA Tel: +1-240-505-0739

India Tel: +91-983-353-0400

www.tcreng.com
Material Testing | Consulting | Inspection | NDT Services

-------------------------------------------

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of SENTHILKUMAR SWAMINATHAN
Sent: Saturday, October 18, 2008 1:16 AM
To: materials-welding@googlegroups.com
Cc: RAGHAVENDRA PEMMARAJU
Subject: [MW:1220] Re: usage of phased array probes in TOFD

PRV,

This is not possible as per me. Better go to www.ndt.net, write in technical disscussion forum some can give you some inputs. That one is purely NDT site.

Regards,

SSK

--- On Sat, 11/10/08, raghavendra pemmaraju <pemma_raghav@yahoo.com> wrote:

From: raghavendra pemmaraju <pemma_raghav@yahoo.com>
Subject: [MW:1210] usage of phased array probes in TOFD
To: "materials-welding@googlegroups.com" <materials-welding@googlegroups.com>
Date: Saturday, 11 October, 2008, 9:35 PM

Whether any one belonging to this group used the above combination for performing TOFD by using Phased Array probe. If so pl.share the experience and procedure.

regards,

Raghavendra

Send free SMS to your Friends on Mobile from your Yahoo! Messenger. Download Now! http://messenger.yahoo.com/download.ph

***DISCLAIMER NOTICE ***
"This e-mail and any files transmitted with it is confidential and is intended only for the use of the recepient(s) named above.
If you are not the intended recipient, any review, retransmission, dissemination, distribution, printing, copying or use the information contained in this message or any part thereof in other manner is strictly prohibited.
If you receive this e-mail in error, please notify the sender immediately by return e-mail and delete the e-mail and any of its attachments.
Any personal views or opinions expressed by the sender shall be understood as neither given nor endorsed by KNM or any of the companies within the Group."

--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog