Please use E7018-1 electrode as we have used it in past.Dont do R&D now.
Also we had not gone for any PWHT after welding. The cast part is functioning in service after repair (almost a year back).
If u do PWHT, it is always better.
Regards
Prem Nautiyal
On Tue, 14 Oct 2008 greetings wrote :
>Prem ,
>
> Thanks for your suggestion
>Can I use E 8018 G electrode with preheat temp 70 (Min) & Interpass Temp 500
>(Max)
>
>
>Regards
>DST
>
>On Mon, Oct 13, 2008 at 7:41 PM, PREM SHANKARDUTT NAUTIYAL <
>prem_nautiyal@rediffmail.com> wrote:
>
> >
> > Dear Friend
> >
> > ASTM A 148 is a ferritic-pearlitic carbon steel for cast products. It is
> > used for higher pressures and stress parts like crane wheels,etc..
> > I think the chemical composition is C=0.4-0.5, Mn=0.4-0.8,
> > Si=0.2-0.5,P&S=max.0.090.
> >
> > First you should arrest the crack by drilling two holes,remove the crack by
> > hand grinding, ensure crack removal by LPT.
> > Preheat the job to 250 degrees celcius, Use E7018-1 electrodes,Interpass
> > temp of 250 degrees celcius and weld. After welding cover the job with
> > asbestos cloth for slow cooling.
> > I am suggesting you this procedure because we had repaired one cast steel
> > of similar composition in the past.
> >
> > Any suggestions / expert comments are welcome...
> >
> > Cheers
> >
> > Prem Nautiyal
> > Godrej, Mumbai
> > Cell: 9820313278
> >
> > On Sun, 12 Oct 2008 greetings wrote :
> >
> > >Friends,
> > > Crack observed in casting material ASTM A 148 GR 80-40
> > >Can any one give the process to rectify the crack (welding
> > electrode,Preheat
> > >Temp & etc)
> > >
> > >Regards
> > >DST
> > >
> > >> >
> >
> > PREM S NAUTIYAL
> > CELL : 9820313278
> >
> > [image: Black578x38_banner2.gif]<http://adworks.rediff.com/cgi-bin/AdWorks/click.cgi/www.rediff.com/signature-home.htm/1050715198@Middle5/2606998_2599290/2602379/1?PARTNER=3&OAS_QUERY=null>
>
>>
PREM S NAUTIYAL
CELL : 9820313278
 |
--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---
Popular posts from this blog
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
------------------------------------- Interpretation: I‑89‑14 Subject: Section I (1986 Edition, 1987 Addenda), PW‑11, NDE Prior to PWHT Date Issued: December 15, 1988 File: BC88‑393 Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39? Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation: VIII-1-98-09 Subject: Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE ...
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
Comments