Skip to main content

Re: [MW:31169] API 6A MONOGRAMMED COMPONENTS MATERIAL CLASS INTERCHANGEABILITY

By Materials & Welding

Dear Hegde,

I m not talking about PSL-1, 2, 3, 3G, 4 (product specification level) or PR-1, 2 (performance requirement).

Its only about Material Class.

regards
raj
On Tuesday, 21 July 2020, 09:05:53 pm GMT+8, 'Prakash Hegde' via Materials & Welding <materials-welding@googlegroups.com> wrote:


Hi 
e.g PS1 ,PSL2 PSL3  and its catagory 
If you require matl  as per PSL2  and mfgr gives you PSL3 it is acceptable but not vice versa

Regards

Hegde



On Tuesday, 21 July, 2020, 06:04:08 pm IST, 'raj susi' via Materials & Welding <materials-welding@googlegroups.com> wrote:


Dear Experts,

Good day to you all!

I have a concern, where the material class of API 6A product scenario is as per below table,

Can I accept the if the Manufacturer gives a higher/lower class for Main/Sub level components against PO requirement?

I m very well aware that Client may say it must be as per PO requirements, and some clients may accept if they get a higher class product is given for the same price. But I d like to know what does API say about this?

Please explain what all can be done in this kind of situations.

Inline image

thanks and regards
raj

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/233184883.3234635.1595333391667%40mail.yahoo.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/1639706948.4233309.1595336614986%40mail.yahoo.com.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

[MW:5202] RE: 5200] NDT after PWHT

By Materials & Welding
------------------------------------- Interpretation:  I‑89‑14 Subject:         Section I (1986 Edition, 1987 Addenda), PW‑11,                  NDE Prior to PWHT Date Issued:     December 15, 1988 File:            BC88‑393   Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39?   Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation:  VIII-1-98-09 Subject:         Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE                 ...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more