Skip to main content

RE: [MW:27794] RE: 27787] Welding oF dissimilar metal at High temperature(Micro Alloy+P11)

By Materials & Welding

You should use Incolnel 82/182 or Inconel 112electrode /matching filler for such dissimilar joint. Note procedure qualification on these cast tubes are extremely difficult. There're some guidelines developed by API for similar alloys in petroleum industry, which may be referred for developing proper welding guidelines.

 

Thanks.

 

P.Goswami.P.Eng, IWE.

Welding & Metallurgical Specialist

Linkedin: https://www.linkedin.com/in/pradip-goswami-2999855/

Email:pgoswami@quickclic.net,pradip.goswami@gmail.com

 

From: 'Asif Shahzad' via Materials & Welding [mailto:materials-welding@googlegroups.com]
Sent: May 7, 2018 3:34 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:27789] RE: 27787] Welding oF dissimilar metal at High temperature(Micro Alloy+P11)

 

Dear Sir,

 

The tubes are centrifugally cast and chemical composition  is  below.

 

Grade G 4852 Micro(25Cr 35Ni Nb)

 

C 0.45,Si 0.7,Mn 1.5

Cr25, Ni 35,Nb1

P 0.03,S0.03,W0.6,Ti,0.3,

Pb 0.01,Sn,0.01,Zn,0.01

 

 

Regards,

 

Asif Shahzad

 

 

On ‎Sunday‎, ‎May‎ ‎06‎, ‎2018‎ ‎06‎:‎38‎:‎15‎ ‎PM, PGoswami <pgoswami@quickclic.net> wrote:

 

 

What's the micro alloy to be welded? What' the manufacturing condition. Could you attach the MTR or any other appropriate details?

 

Thanks.

 

 

P.Goswami.P.Eng, IWE.

Welding & Metallurgical Specialist

Linkedin: https://www.linkedin.com/in/pradip-goswami-2999855/

Email:pgoswami@quickclic.net,pradip.goswami@gmail.com

 

From: 'Asif Shahzad' via Materials & Welding [mailto:materials-welding@googlegroups.com]
Sent: May 6, 2018 4:41 AM
To: Materials & Welding <materials-welding@googlegroups.com>
Subject: [MW:27787] Welding oF dissimilar metal at High temperature(Micro Alloy+P11)

 

Dear Expert,

 

We want to weld Micro alloy (Ni,Cr) furnce tubes with the P11reducer in the Steam methane reformer that will be operator at 850 to 900 C temperature.

Please provide your opinion about welding reliability of these two dissimilar   metal at high teperature.

 

Regards,

Asif Shahzad 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

[MW:5202] RE: 5200] NDT after PWHT

By Materials & Welding
------------------------------------- Interpretation:  I‑89‑14 Subject:         Section I (1986 Edition, 1987 Addenda), PW‑11,                  NDE Prior to PWHT Date Issued:     December 15, 1988 File:            BC88‑393   Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39?   Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation:  VIII-1-98-09 Subject:         Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE                 ...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more