Skip to main content

RE: [MW:24874] Material Grade for RE-bar---AWS D1.4

By Materials & Welding

內嵌影像

寄件者： JIJILAL KM <jijilalkm2@gmail.com> 收件者： materials-welding@googlegroups.com 寄件日期： 2016年5月25日（週三）下午12:32 主旨：回复：[MW：24861]材料牌號為RE-酒吧

親愛的穆罕默德，

ASTM A615級60是焊接等級重新類似於BS 4449條。


JIJILAL  KM 
QA / QC經理，
泰國裕廊工程有限公司，
KCE SPP項目，泰國
＃096 786 0129


在2016年5月在10:24，"穆罕默德·阿里·"通過材料與焊接25 < materials-welding@googlegroups.com >寫道：
尊敬的專家，
 
我們的民政部門需要重新焊接桿重新酒吧BS 4449-2005級，請幫我找到找到合適的WPS以"P"號相當於ASTM標準。


感謝和問候，穆罕默德·阿里·Samsudeen
 
- http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm 的意見表達/ exchnaged該組中的成員企業人事的意見和意味著僅用於教育目的，用戶必須考慮自己的決定WRT適用碼/標準/合同文件。 --- 因為你訂閱了谷歌論壇"材料與焊接"組。您收到此消息， 要退訂此論壇並停止從中接收電子郵件，發送電子郵件到材料的焊接+unsubscribe@googlegroups.com。 要在此論壇發帖，請發送電子郵件至materials-welding@googlegroups.com。 在網絡上查看此討論 更多選擇，請訪問https://groups.google.com/d/optout。









- http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm 的意見表達/ exchnaged該組中的成員企業人事的意見和意味著僅用於教育目的，用戶必須考慮自己的決定WRT適用碼/標準/合同文件。 --- 因為你訂閱了谷歌論壇"材料與焊接"組。您收到此消息， 要退訂此論壇並停止從中接收電子郵件，發送電子郵件到材料的焊接+unsubscribe@googlegroups.com。 要在此論壇發帖，請發送電子郵件至materials-welding@googlegroups.com。 在網絡上查看此討論 更多選擇，請訪問https://groups.google.com/d/optout。










Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

[MW:5202] RE: 5200] NDT after PWHT

By Materials & Welding
------------------------------------- Interpretation:  I‑89‑14 Subject:         Section I (1986 Edition, 1987 Addenda), PW‑11,                  NDE Prior to PWHT Date Issued:     December 15, 1988 File:            BC88‑393   Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39?   Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation:  VIII-1-98-09 Subject:         Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE                 ...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more