Re: [MW:13560] need your help please : Can I take CSWIP 3.2 without hold CSWIP 3.1 ?

Dear Mr Mohmad,

First try to aquire 3.1 and then try 3.2. In 3.2 itself there are 2 category do you know that? so please try 3.1 and try 3.2 with RT or without RT interpretation. Because many dont get 3.1 eventhough they have got very good qualifications and experiences so I would suggest you to attend the course where you would gain something that you dont learn in college and field of welding.

Good luck

Regards

On 23 January 2012 14:17, sajidalam mohd. <engineer_makes_world@yahoo.co.in> wrote:

yes you can write 3.2 directly.but you have to subbmitt required documents.

regards

md.sajid alam

From: mohamed maher <mohamed.ahmed.maher@gmail.com>
To: Materials & Welding <materials-welding@googlegroups.com>
Sent: Sunday, 22 January 2012 3:08 PM
Subject: [MW:13541] need your help please : Can I take CSWIP 3.2 without hold CSWIP 3.1 ?

dear, all
I need to take CSWIP 3.2 but I am not certified CSWIP 3.1 and
according to Requirements for the Certification of Visual Welding
Inspectors, Welding Inspectors and Senior Welding Inspectors (fusion
welding) - (Document No CSWIP-WI-6-92 11th Edition September 2011).
Implementation Date September 2011 ,
I can take CSWIP 3.2 directly with no need to be certified with CSWIP
3.1 if i have 5 years experince .

My question now , I want to take the exam of CSWIP 3.2 and I am
not certify with CSWIP 3.1 and I have more than 6 years experince .

Thank you for your time and consideration ,Looking forward to hear
from you.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...

Materials & Welding

Search This Blog