RE: [MW:11123] RE: 11080] SA-213 Gr.T91

I have confirmed with ASME that this an error – it will be corrected in the 2011 edition of Sc IX.

Use P-No. 15E

John

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Vanchinath S.A.
Sent: Saturday, May 21, 2011 10:02 PM
To: materials-welding@googlegroups.com
Subject: Re: [MW:11111] RE: 11080] SA-213 Gr.T91

P no. 15E is correct

vanchi

On Wed, May 18, 2011 at 9:51 PM, John Henning <jhenning@deltak.com> wrote:

Appears to be an error. All UNS K90901 (“91” alloy) were to be changed to P-No. 15E with publishing of 2009 Edition.

Use P-No. 15E

John

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of srinivasu
Sent: Wednesday, May 18, 2011 4:40 AM
To: materials-welding@googlegroups.com
Subject: [MW:11080] SA-213 Gr.T91

Dear Experts

What's the P.No. of Material Specification of SA-213 Gr.T91?

I refer Sec.IX 2010 Edition as per QW-422 - it's P.No.5B Gr.No.2

as per Appendices-D - it's mentioned P.No.15E Gr.No.1

Which one is the correct?

With Regards

Srinivasu V

Welding Engineer

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

[MW:5202] RE: 5200] NDT after PWHT

------------------------------------- Interpretation: I‑89‑14 Subject: Section I (1986 Edition, 1987 Addenda), PW‑11, NDE Prior to PWHT Date Issued: December 15, 1988 File: BC88‑393 Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39? Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation: VIII-1-98-09 Subject: Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE ...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Materials & Welding

Search This Blog