Skip to main content

[MW:3043] Re: 3018] p no

By Materials & Welding
Dear Ali,
Answer to your query...
----------------------------
is it correct that for steels that has a specification another of
asme
II find equivalent steel,P no ?
---------------------------------
Metals that do not appear in ASME Sec IX - P Number Table are
considered to be unassigned metals; the unassigned metal can be
matched with ASME P Number of the table by UNS Number of unassigned
metal. The metals do not having UNS numbers which are not listed in P
Number table can be matched by Chemical & Mechanical properties (UTS)
of the materials that are available in Section II by a comparison
table. Hence, it is correct that a spec of Non ASME material can be
compared with ASME P Numbering system.

Thanks
Senthil


On Aug 27, 8:19 am, ali asghari <asgharial...@gmail.com> wrote:
> Dear all
> is it correct that for steels that has a specification another of asme
> II find equivalent steel,P no ?
> regards.
>
>
>
> On Wed, Aug 26, 2009 at 9:26 AM, Muhammad Ijaz <m_i...@ffc.com.pk> wrote:
> >  Dear Mano,
>
> > As per Stahlschluseel 2007, G4859 is equivalent to A351 (CT15C). So the
> > corresponding P no. shall be P. no. 45 as per ASME IX 2007.
>
> > Regards,
>
> > *Muhammad Ijaz*
>
> >  ------------------------------
>
> > *From:* materials-welding@googlegroups.com [mailto:
> > materials-welding@googlegroups.com] *On Behalf Of *Manoharan Kalimuthu
> > *Sent:* Tuesday, August 25, 2009 9:56 PM
> > *To:* materials-welding@googlegroups.com
> > *Subject:* [MW:3018] p no
>
> > Dear all
>
> > We have material G4859 (its in the ISO) I would like to know what is the P
> > NO for this ....
>
> > Regards
>
> > Mano- Hide quoted text -
>
> - Show quoted text -

--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more