Skip to main content

Re: [MW:31778] Norsok M-601

By Materials & Welding
Dear Sandeep.
Thank you for sharing the link, but the only paragraph which talk about my concern is ''If the composite is a pipe or if it must be welded from one side, the buttering technique should be used. In this case the filler metal must provide an analysis equal to the clad metal and be compatible with the backing steel. Weld passes are made on the edge of the composite to butter the clad and backing metal. The buttering pass must be smoothed to the design dimensions prior to fitup. The same electrode can be used to make the join'' and again you have to deposit carbon steel filler metal on a buttering pass which is an alloyed metal.
I think the statement is not applicable for cladad piping.
Regards.

On Mon, Nov 23, 2020 at 5:17 PM Sandeep Pr <prsandeep61@gmail.com> wrote:

On Mon, Nov 23, 2020 at 7:37 AM Ali Asghari <asgharialigl@gmail.com> wrote:
Dear George.
Thank you for responding, but my question isn't related to your response, actually this statement siad when you have two clad components which want to be welded to each other, first base metal shall be welded and joined ,after that cladded parts.
Now what would be possible for welding of cladded small piping?
Regards,   

On Thu, Nov 19, 2020 at 3:02 PM George Dilintas <dilintas@gmail.com> wrote:
 If you deposit a cladding of 316 or 304 on a carbon steel, you may get hot cracking due to low Ferrite number. Therefore you deposit a layer of 309 which mixed with the carbon steel does not give hot cracking

Στις Δευ, 16 Νοε 2020, 16:38 ο χρήστης asghar...@gmail.com <asgharialigl@gmail.com> έγραψε:
Dear All.
Would you say what is the reason of this statement" When welding clad materials from both sides, the C and CMn steel shall be completely welded prior to welding the cladding. C or CMn steel or low alloyed steel weld metal shall not be deposited onto a high alloy base material or weld metal.'' ?
How is it possible for cladded piping?
Regards,

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/4d8f2d92-d9ee-4ec7-89ca-ebdddd25d516n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to a topic in the Google Groups "Materials & Welding" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/materials-welding/cHRITpDcpLU/unsubscribe.
To unsubscribe from this group and all its topics, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAPOi40AuqmjYA5cN4ciu_swJ0i%3DHQ6TFJqPFQ5fOD7Z57XWUUw%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CALcH7WD8bbTqFWLiZ_H-0OxUU5H0QbNM7qKsp9ubBDqMLCf0Aw%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to a topic in the Google Groups "Materials & Welding" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/materials-welding/cHRITpDcpLU/unsubscribe.
To unsubscribe from this group and all its topics, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAFBEtQowRdWOo9-Y_N5Uh-fNzcVu3PnChZZ1N7ivwnG-xODOpA%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CALcH7WCuHuunosi1PjpsjmwqiCUG7%3DwPXgs7ZPV-2%2BNpJDi6XA%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more