I had a query related to same subject. one of our client is asking 2 cases in same socket weld joint configuration. at the time of fit up we need th make sure those things. the main points are follows,,same time i attached a sketch from ASME B 31.3- 328-5-2A WITH MARKED.
1. GAP BETWEEN INNER DIAMETER OF SOCKET AND OUTER DIAMETER OF PIPE.
2. PENETRATION AT THE ROOT .
is this mentioned in Any International standards or Company specification. ? if that just share to me ..
Below interpretation of B 31.3 and Shell std. Extract are quite convincing for subject matter.
1. B 31.3 Interpretation
2. As per SHELL Spec DEP 31.38.01.11 Gen. Aug 2005
Socket-welded connections cannot be properly radiographed to verify weld quality; they can only be inspected by surface techniques such as magnetic particle or liquid penetrant. Radiography may be selectively applied to check that a fit-up gap remains after the weld has been made.
Regds/Jignesh
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of John Henning
Sent: 25 September 2012 19:07
To: materials-welding@googlegroups.com
Subject: RE: [MW:15392] Re: Socket weld gap requirement
All of the following require a 1/16 inch minimum gap prior to welding for socket type joints: ASME I, ASME VIII, ASME B31.1, ASME B31.3. None of these Codes address the condition after welding. My familiarity with the Code would indicate that this is intentional as it is generally recognized that the joint often will close completely after welding.
Customer's can demand anything, whether rational or not. In many cases the customer will assume if there is no gap after welding the socket weld was not properly gapped prior to welding (where were their inspectors during fit-up?) . Physics be damned. No amount of scratch marking etc. will convince these customers. The only way is to gap to greater extent or through the use of gap-o-letsÒ.
Bottom line: read your customer specifications carefully before you begin fabrication.
John A. Henning
Welding & Materials
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Pradeep kumar hormis
Sent: Tuesday, September 25, 2012 2:32 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:15386] Re: Socket weld gap requirement
Sir
I would like to know , any criteria for maintaining the GAP between ID of female part and OD of pipe or male part especially in SOCKET joints.. Any standards or specification given details of it?. There was an issue between client inspector and contractor.On Mon, Sep 24, 2012 at 5:50 PM, John Henning <jhenning@deltak.com> wrote:
The statement in Saudi Aramco Clause C2 is correct.
More often than not, the gap will "disappear" after welding. The common misconception is that you must have the gap after welding. The purpose of the gap is to permit shrinkage of the weld without creating additional mechanical stresses on the finished joint. Obviously, in weldor parlance, if the joint "sucks in" the gap will close.
Note that at one time, the EPRI NDE center was doing some investigation into the necessity of gaping socket joints. The opinion at that time was that the gap was unnecessary and that this "rule of thumb" was a nearly universal myth. If memory serves me correctly, the recommendation was that a more important modification for socket joints was to make the length of the horizontal leg of the weld twice the length of the vertical leg. This type modification was reportedly very effective especially in minimizing fatigue cracking. I wouldn't mind knowing if this has been investigated further or if there was any additional information published on this.
John A. Henning
Welding & Materials
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Pradeep kumar hormis
Sent: Monday, September 24, 2012 3:14 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:15378] Re: Socket weld gap requirement
Dear All
I would like to introduce my self first. I am working as QC WELDING INSPECTOR for one of SAUDI ARAMCO project. we are using most of socket joints for plant piping . SAUDI ARAMCO having special standards , procedures and check lists for all the cases. so here i attached one of the check list for socket joints fit ups. even it is a client specification , I hope you will get help for your clarification. please note the CLAUSE -C2 on the SAIC.On Sun, Sep 23, 2012 at 7:20 PM, Hernan Arturo Castillo Mier <Hernan.Castillo@ecopetrol.com.co> wrote:
Your information is not true.
The gap its necessary for thermal expansion of tube been welded according to the operation temperature.
Its necessary to calculate the expansion expected according to the op temp.
Enviado desde mi iPhone
El 23/09/2012, a las 10:28 a.m., "ranendrac6@gmail.com" <ranendrac6@gmail.com> escribió:
> The gap is required to release the fume gases which generated during welding. No gap required after welding(I don't see any reason). You can check with 4 mm gap during fit up to meet client requirement.
> Sent on my BlackBerry® from Vodafone
>
> -----Original Message-----
> From: Raghuram Bathula <raghurambathula@gmail.com>
> Sender: materials-welding@googlegroups.com
> Date: Sun, 23 Sep 2012 08:10:03
> To: Materials & Welding<materials-welding@googlegroups.com>
> Reply-To: materials-welding@googlegroups.com
> Subject: [MW:15368] Re: Socket weld gap requirement
>
> no it it not required after welding, many times gap closes to zero due
> to shrinkage during welding. if your client requires the gap after
> welding (I don't see any reason for this) probably you need fit up
> with more gap.
>
> On Sep 22, 7:49 pm, Naresh Kumar <snareshkuma...@yahoo.com> wrote:
>> Dear experts,
>>
>> As per ASME 3.1.& 31.3 socket weld gap requirement is
>> 1/16" before welding. Whether it is required for after welding, if its require
>> kindly provide the code details.In our project we're done RT for socket welds. But
>> after welding did not find the 1/16" gap,
>> its less than 0.5mm. Our client decision is to cut and reweld the all joints.
>>
>>
>> Thanks & Regards,
>> Naresh
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at http://materials-welding.blogspot.com/
> http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
>
> The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
>
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at http://materials-welding.blogspot.com/
> http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
>
> The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
>
>
>Este mensaje y sus anexos está dirigido para ser usado por su(s) destinatario(s) exclusivamente y puede contener información confidencial y/o reservada protegida legalmente. Si usted no es el destinatario, se le notifica que cualquier distribución o reproducción del mismo, o de cualquiera de sus anexos, está estrictamente prohibida. Si usted ha recibido este mensaje por error, por favor notifíquenos inmediatamente y elimine su texto original, incluidos los anexos, o destruya cualquier reproducción del mismo. Las opiniones expresadas en este mensaje son responsabilidad exclusiva de quien las emite y no necesariamente reflejan la posición institucional de Ecopetrol S.A. ni comprometen la responsabilidad institucional por el uso que el destinatario haga de las mismas. Este mensaje ha sido verificado con software antivirus. En consecuencia, Ecopetrol S.A. no se hace responsable por la presencia en él, o en sus anexos, de algún virus que pueda generar daños en los equipos o programas del destinatario.
This e-mail, and any attachments thereto, is intended for use by the addressee(s) named herein only and may contain legally privileged and/or confidential information. If you are not the recipient of this e-mail, you are hereby notified that any distribution or copying of this e-mail, and any attachments thereto, is strictly prohibited. If you have received this e-mail in error, please notify us immediately, permanently delete the original including attachments, and destroy any copy or printout thereof. The opinions contained in this message are the sole responsibility of the individual person who gives them and do not either necessarily reflect the institutional policy of Ecopetrol S.A. on the subject, or involve corporate responsibility for any use of them by the addressee(s). This message has been checked with antivirus software; therefore, Ecopetrol S.A. is not liable for the presence of any virus in the message or in its attachments that causes or may cause damage to the recipient's equipment or software.
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--Thanks & Regards
PRADEEPKUMAR HORMIS
QC WELDING INSPECTOR
ARAMCO PROJECT(JEDDAH REFINERY)
Mob:+966 - 59 11 36 36 9
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
______________________________________________________________________
The information in this email is confidential, and is intended solely for the addressee(s). If you are not the intended recipient of this email please let us know by reply and then delete it from your system; you should not copy this message or disclose its contents to anyone. The internet can not guarantee the integrity of this message. HAMON (and its subsidiaries) shall (will) not therefore be liable for the message if modified.
______________________________________________________________________--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--Thanks & Regards
PRADEEPKUMAR HORMIS
QC WELDING INSPECTOR
ARAMCO PROJECT(JEDDAH REFINERY)
Mob:+966 - 59 11 36 36 9
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
______________________________________________________________________
The information in this email is confidential, and is intended solely for the addressee(s). If you are not the intended recipient of this email please let us know by reply and then delete it from your system; you should not copy this message or disclose its contents to anyone. The internet can not guarantee the integrity of this message. HAMON (and its subsidiaries) shall (will) not therefore be liable for the message if modified.
______________________________________________________________________--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
PRADEEPKUMAR HORMIS
QC WELDING INSPECTOR
ARAMCO PROJECT(JEDDAH REFINERY)
Mob:+966 - 59 11 36 36 9
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
No comments:
Post a Comment