For mainline, we used 40" dia X65/1" WT root 6010, remaining 8018G. Regards, S.Senthilkumar
--- On Mon, 23/3/09, hakan sitem <hakansitem@yahoo.com> wrote:
From: hakan sitem <hakansitem@yahoo.com>
Subject: [MW:1796] Re: Query on SMAW electrode selection for API 5L X65
To: materials-welding@googlegroups.com
Date: Monday, 23 March, 2009, 1:43 PM
| Hi, pls note the following applications; Mainline Welding: | Steel Grade | Root Pass | Hot Pass | Filling | Cap | | | | | | | | X42/X52 | Pipeweld 6010 | Pipeweld 7010 | Pipeweld 7010 | Pipeweld 7010 | | X60/X65 | Pipeweld 6010 | Pipeweld 8010 | Pipeweld 8010 | Pipeweld 8010 | | X70 | Pipeweld 6010 | Pipeweld 9010 | Pipeweld 9010 | Pipeweld 9010 | | | | | | |
Weld area strengths and properties should be observed. So we will focus on "Total Weld Metal Area" and also HAZ for the required
--- On Sun, 22/3/09, ARI <ariv2k@gmail.com> wrote:
From: ARI <ariv2k@gmail.com>
Subject: [MW:1792] Re: Query on SMAW electrode selection for API 5L X65
To: materials-welding@googlegroups.com
Date: Sunday, 22 March, 2009, 9:43 AM
Hi, Using E6010-G would keep the dilution level as minimum, but at the same time, it wouldn;t give the UTS equal to Parent metal UTS for API5L X65?
Regards, Ari On 3/21/09, babu k <kbabupsg@gmail.com> wrote:
Hi,
Put it in simple words, the use of E6010-G is to keep the dilution level to be minimum ; Thanks & Regards, K.Babu Singapore
On Thu, Mar 19, 2009 at 6:15 PM, Ari <ariv2k@gmail.com> wrote:
Dear All,
Can you please advise, why E6010-G (root) & E-7010-P1 (hot/fill) are
used for Oil pipelines(Sour) containing parent material of API 5L X65.
Since these type of PQR/WPS are being approved by most of the
Company.
As, X65 has an YS of 65,000 Psi, whilst the electrodes used E6010 has
YS of 48,000 Psi, and E-7010-P1 has YS of 60,000 psi. By using both
of these electrodes the weld metal strength would not exceed YS
60,000 psi.
How its acceptable to keep the low weld metal strength(<YS 60,000 Psi)
than the parent metal (= YS 65,000Psi).
Thy suppose to use E8010 for root and E8018 for hot/fill, for API 5L
X65 materials, which only would give the equivalent WM strength.
As we all know that overmatching weld metal strength causes gross
section yielding in the pipe, whereas Undermatching weld metal
strength will cause straining of the weld.
Your advise/suggession, based on experience is appreciated.
Regards,
Ari
|
Connect with friends all over the world. Get Yahoo! India Messenger. --~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---
Popular posts from this blog
Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
|
Comments