Re: [MW:35613] DISSIMILAR WELDING IN STRUCTURAL

I truly appreciate your quick response and confirmation. Thank you for your understanding and support.

On Thu, May 15, 2025 at 7:13 AM Parminder Singh <parmsin2021@gmail.com> wrote:

Dear Akhilesh ji,

WPS is OK but from next time, Do always mention the deposited weld metal thickness for each process.
Here, Fillet must be of atleast 6 mm (Plate is 6mm and Pipe is 5.54 mm) so Use GTAW only.

Thanks

On Wed, May 14, 2025 at 3:59 PM Akhilesh Kumar <akhileshlikes@gmail.com> wrote:
Greetings Experts,
I would like to bring your attention to and clarification about the below-mentioned materials required for welding in the structural platform for Instrument support. In which required earthing clit/plate (6mm THK X 50mm H X 65mm W SS316) to be welded with pipe (API 5L Gr B Thk- 5.54 MM) and channel (PFC 100x50x10mm THK). ASTM A 572 GR 50).
Could you please confirm that the mentioned piping WPS can be used for above mentioned ?

Thank you for your response and suggestion.
WBR,
Akhilesh K.
+918172813538

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/materials-welding/CAE1xz0NaaoTUsRBSx%3D7KYtG%2BDCmyr-S2gS2GwRomtpfzzWWjhg%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/materials-welding/CAGAT7zfOQFR_y87HCFZSASmk4h2hjxL9ncY2zMZiDXnYSgoJiw%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/materials-welding/CAE1xz0PBcq08Kkxjhsf5emx3L7mQUgHa_xUFY5wi4%3D7AxnJwgQ%40mail.gmail.com.

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

[MW:5202] RE: 5200] NDT after PWHT

------------------------------------- Interpretation: I‑89‑14 Subject: Section I (1986 Edition, 1987 Addenda), PW‑11, NDE Prior to PWHT Date Issued: December 15, 1988 File: BC88‑393 Question: Does PW‑11 require that NDE be performed on welds after they have been subjected to the postweld heat treatment required by PW‑39? Reply: No, unless the conditions described in PW‑11.2.2 exist. ---------------------------------------------- Interpretation: VIII-1-98-09 Subject: Section VIII, Division 1 (1995 Edition, 1996 Addenda); NDE ...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Materials & Welding

Search This Blog