Re: [MW:14203] Welding C45 (1045)

Hi you got a Carbon content of .45....use an Austernetic stainless
steel consumable because it gives more ductility and and less strength
and it will relieve internal stress.but your HAZ zone will still be
brittle so you have to do a PWHT(stress relief)temperatures for stress
relief range between 550-750 degrees Celsius ..Note 1 hour for every
25mm of thickness so you do the maths and you ll be fine...this is
according to procedure

Salman
Gem Consulting

Mon, May 7, 2012 at 7:10 PM, prem nautiyal <prem_nautiyal26@yahoo.com> wrote:
> Hi
>
> Increase the preheat to 150 degrees Celcius min. Interpass temp 250 degrees
> celcius max.
> Use SMAW E7018-1 electrode.
>
> I have successfully welded C45 material with E7018-1.
>
> Regards
>
> Prem Nautiyal
>
> From: LeONarD P <metpick@gmail.com>
>
> To: Materials & Welding <materials-welding@googlegroups.com>
> Sent: Saturday, May 5, 2012 10:56 AM
>
> Subject: [MW:14187] Welding C45 (1045)
>
> Dear All expert
>
> Welding C45 (1045) steel (Pivot Boss) to S275JR (main
> structure)
>
> 1045 Pivot Boss is casting part.
> S275JR is steel plate
>
> For a project I need to weld a C45 (1045 steel, 0.45% carbon Thick 100
> mm) on a S275JR steel ( Thichness 30 mm.)
>
> Joint design & condition weld: T-butt joint, double bevel, CJP. Bevel
> at S275JR steel.
> preheat 110 C
> minimum,. interpass temp 220 C max.
> by FCAW process.
> A5.20 / E71T-1C
>
>
> After weld, the problem is crack appear along on surface casting
> part (1045 steel)
>
> How to solve this problem.
>
> Thank you very much.
> leonardd..
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to
> materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at
> http://materials-welding.blogspot.com/
> The views expressed/exchnaged in this group are members personel views and
> meant for educational purposes only, Users must take their own decisions
> w.r.t. applicable code/standard/contract documents.
>
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to
> materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at
> http://materials-welding.blogspot.com/
> The views expressed/exchnaged in this group are members personel views and
> meant for educational purposes only, Users must take their own decisions
> w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog