Re: [MW:34357] Crack Repair

Dear Sir,

Please provide sketch of Crack location and Materials grade and service of the HE.

Thickness and if any of API 934 series apply

Thanks

A.Eissa

On Tue, Jun 20, 2023 at 10:48 AM, Ashish Chacko
<iamashleo007@gmail.com> wrote:

Request for Expert Advice on Crack Repair
I am writing to request the support of the experts out here on a crack repair in an exchanger. The exchanger has a fillet weld with the shell, and a crack was found during the last TAM. There is a possibility that the crack will be found again during this TAM.
The base material of the exchanger is 58mm P1 (A516-GR 70) with cladding of SS347 of 6mm. There are two scenarios to consider:
Scenario 1: Localize repair of the ring chamber fillet weld by grinding and welding. The client is requesting for annealing after the repair. Is this really required?
Scenario 2: If the crack propagates to the shell, the client is asking for DHT and PWHT. When should DHT be performed, before or after the cladding weld? Is there any exemption for PWHT?
I would be grateful for any advice that you can provide on these two scenarios. Thank you for your time and consideration.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/4010c4b0-e975-43fb-8399-b75840f3fc24n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/1001025488.2307612.1687251118772%40mail.yahoo.com.

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

[MW:36169] Cold Bending Qualification

Dear Experts, Can anyone share the inspection requirements or a qualification procedure for cold bending? Our client spec states only the requirements for induction bending and would like to know your opinion on the cold bend inspection requirements. The code of construction is B31.3, Max. 5D bends, A106 SS 316L. Thanks in Advance. -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion visit https://groups.google.com/d/msgid/materials-welding/1be61cc3-e9c9-4a5f-834d-e8485e248432n%40googlegroups.com .

[MW:30043] Weep hole

If weep hole is not provided in dummy pipe before welding What will happen??? -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/da251ee6-fa7f-4851-b876-cdb3834ae341%40googlegroups.com .

Materials & Welding

Search This Blog