Skip to main content

[MW:18040] FW: Share FREE Asset Integrity Information

By Materials & Welding
Hi Everyone
 
This is a nice journal, off course subscription based. Those who want to subscribe and have the full access may do so by contacting Mr.. Alavaro.
 
Enjoy.
 
Thanks.
 
 
Pradip Goswami, P.Eng,IWE
Welding & Metallurgical Specialist
Ontario, Canada
pgoswami@quickclic.net
pgoswami@sympatico.ca
 
 

From: Tyler Alvarado [mailto:talvarado=inspectioneering.com@mail202.atl21.rsgsv.net] On Behalf Of Tyler Alvarado
Sent: Wednesday, June 26, 2013 3:59 PM
To: Pradip
Subject: Share FREE Asset Integrity Information

Share free AIM info with colleagues.
View this email in your browser

Share Inspectioneering Turnaround 


I want to ask a favor: share our free newsletter, Inspectioneering Turnaround.

You read it. You know it's full of technical content, news, and the latest on asset integrity management. I'm just asking you to forward this email to others who want AIM info. Best of all, it's free and sign up takes less than a minute when you go to:

www.inspectioneering.com/turnaround

Sharing AIM intelligence is part of our mission here at Inspectioneering. Thank you for your help and for being part of our community.

Best,

Tyler A. Alvarado, Director
Inspectioneering, LLC
talvarado@inspectioneering.com
www.inspectioneering.com
Office: 281-397-7075

Inspectioneering, LLC
701 Sawdust Rd, Ste. 4 / The Woodlands, TX 77380 / 281-397-7075 / www.inspectioneering.com 

unsubscribe from this list    update subscription preferences 


Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more