Skip to main content

RE: [MW:31100] Re: Coating on welds prior to hydro test API code

By Materials & Welding

API does not have any piping design & construction code. API-570 is on post construction , maintenance and inspection. Hence ASME  B-31.3 is followed commonly for fabrication, inspection and testing.

According  to B 31.3 – Clause  345.3 Preparation for Leak Test

 

345.3.1 Joints Exposed:- (d) All joints may be primed and painted prior to leak testing unless a sensitive leak test (para. 345.8) is required.

345.8 Sensitive Leak Test: The test shall be the Bubble Test.

 

Thanks.

 

P.Goswami.P.Eng, IWE.

Independent  & Consulting Welding & Metallurgical Specialist

Aramco Approved Designated Project Welding Engineer(DPWR)

Linkedin: https://www.linkedin.com/in/pradip-goswami-2999855/

Email:pgoswami@rogers.com,pradip.goswami@gmail.com

Cell/Whasapp:1-905-9793232

 

 

 

From: materials-welding@googlegroups.com <materials-welding@googlegroups.com> On Behalf Of madhan chozhan
Sent: July 4, 2020 6:32 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:31097] Re: Coating on welds prior to hydro test API code

 

Code of construction  - ASME B 31.3 but need to know if any API code governs the piping construction and related testing requirements.

 

Thanks,

Madhan

 

On Sat, Jul 4, 2020 at 8:15 AM Materials & Welding <materials-welding@googlegroups.com> wrote:

what is your code of construction?

On Friday, 3 July 2020 at 09:26:29 UTC+5:30 madhan wrote:

Dear Experts,

 

Can you throw some light on the subject? Does any API code specify about the coating requirements on welds prior to hydro testing?

 

Material - A106 Gr B, A519 Gr 4130.

 

Thanks,

Madhan

 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/5bd85622-f5bd-43cd-bb64-4e1abaec68dfn%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CABnNWHXwWUOS4NqVkYTYYzoFmmE6uVVmwO%3Ds050YGXsTGmv3Uw%40mail.gmail.com.


Virus-free. www.avg.com

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more