Skip to main content

Re: [MW:30418] Base material for Welder Qualification

By Materials & Welding
Check out QW 380/381 of Sec IX as well to take note of the essential variables  mentioned therein.
Thanks 
Amitabh

On Wednesday, January 22, 2020, 05:56:31 AM EST, Sajeev P <sajeevlaxmi@gmail.com> wrote:


Greetings, 

As per Sec. IX, you have to qualify the welders in accordance with QW-301 for joining  the base material portion of the cladded  pipe. And for welders  who will apply  the cladded  portion  of a weld between  clad materials,  shall be qualified  in accordance with QW-381.

If the welder is qualified on P1 material, then the welder is qualified to  weld only  base material portion  of the  cladded pipe. 

The welders can qualify  as per QW-301 & QW-381 separately  or alternatively  the welders may qualify  using cladded test coupon of at least  3/8in. (10mm)  thick  and of dimension such that  a groove weld can be made to join  the base  material  and the corrosion resistant  weld metal overlay can be applied to the completed groove weld as per QW-383.

Regards, 
Sajeev  


On Wed, Jan 22, 2020, 09:20 Babu Chathoth <babu8803@gmail.com> wrote:
Hi friend,

can anybody can assists to clarify , is it applicable for the only P1 material can use for the WQT test for  P1 material with clad pipe  approved WPS ,

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/56526bac-5085-413d-80e7-995e94304506%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CANSvUP39VDd26DZvsAhxb9rOEz-Xur7-QJu%2BX4_MKVwqGQ_eew%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more