Re: [MW:34498] Re: ER70S-2 and ER70S-6 (GTAW Process)

ER70S-2 filler wire is mainly used for single-pass welding of killed, semi-killed, and rimmed steels. 

The addition of deoxidizer allows the filler metal to be used for welding steel with rust or dirt on the 

surface, which may damage the weld quality, depending on the surface conditions. It is widely used 

for high-quality and high-toughness GTAW welds and is well suited for single-side welding without 

the need for root gas protection on the reverse side of the joint. .

ER70S-6 filler wire is suitable for both single-pass and multi-pass welding. They are particularly suitable 

for sheet metal where smooth weld passes are expected and for sheet steel with moderate amounts 

of rust or hot rolled scale. These wires allow for higher current ranges when welding with a CO2 

shielded gas or a mixture of argon, carbon dioxide, and oxygen or argon and carbon dioxide. Typically, 

the base material used is the same as ER70S-2. Well suited for single-side welding without the need for 

root gas protection on the reverse side of the joint.

Further, with the addition of deoxidizers in ER 70S-2, the cost of the wire is three times higher than 

ER70S-6 filler wires.

Sridhar.

--------------------------------------------------------------------------------------------------------------------

On Thu, 17 Aug 2023 at 14:59, Kannayeram Gnanapandithan <kgpandithan@gmail.com> wrote:

generally 70S2 is not being used in GMAW eventhough it calls for both process, Any reasons?

On Wed, Aug 16, 2023, 4:36 PM sridhar cn <sridharcn305@gmail.com> wrote:

Due to triple deoxidizers present in the filler, the ER70S-2 wire is much more suited to weld on rusted surfaces 

compared to ER70S-6. Rust, which is an iron oxide, will react very fast with Ti, Zr, or Al to form their oxides, such 

as TiO₂ or ZrO₂ or Al₂O₃ thus the Mn will be saved. Mn provides strength and toughness to the weldment. So, 

any loss of Mn from the weld deposit will actually reduce the strength of the weld metal.

 

Loss of silicon will make the weld pool sluggish and can result in a poor weld bead appearance. There is no 

difference between ER 70S-6 and ER 70S-2 based on the mechanical properties, as both have 70ksi Tensile 

strength and 58 Ksi Yield strength. Both wires provide equal minimum specified tensile strength, yield strength, 

ductility, and toughness values.

  

ER 70S-6 is a solid TIG rod that is used for general-purpose welding. It can be used on MS, CS and LA  steels.

ER 70S-2 is available in 0.80 to 3.20 mm sizes, whereas ER 70S0-6 is available mostly in 0.80 to 2.00 mm sizes. 

Make a mock-up weld and see whether it meets X-ray qualified welds and check the mechanical properties prior 

to any further action.

 

C Sridhar.

  

On Wed, 16 Aug 2023 at 14:22, Vishwas Keskar Welding Manager WELDING <vvkeskar123@gmail.com> wrote:

You can write ER70S-6 with a note in WPS that :

Mn content shall not exceed 1.6 % 

Si content shall not exceed 1.0 % 

Thanks

VIshwas - IWE 

On Monday, June 3, 2019 at 7:48:39 PM UTC+5:30 K K wrote:

Dear All,

My PQR is qualified with ER70S-2.

Can I use ( Mention) ER70S-6 in WPS.

Regards

Kiran

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/44b55841-6c7a-4e35-8a10-4879eca1ff20n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHo%3DYiia5Vcpp97nXCXzo%3DU685%3D06bsVuZJcWWiYyC%3D%3D62kC1w%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAJzm4eNX3e5%2BrYbf0o_T%3Dwh%3D690hnfAJfoM477gWfpzk-mJY_A%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAHo%3DYiiSjnm23UGwYvL6rFZc%2B7G_NaeLXJ--0Wrd1C7wogpeyA%40mail.gmail.com.