Skip to main content

Re: [MW:34486] ER70S-2 and ER70S-6 (GTAW Process) - A number

By Materials & Welding
it means  need not test weldmetal again while doing PQR. 

On Mon, Aug 14, 2023, 9:32 AM MW <raghurambathula@gmail.com> wrote:
just to update
ASME Boiler & Pressure Vessel Code 2023 Edition Significant changes include:
-Added an optional supplemental "A" designator to indicate that an ER70S-6A electrode or R70S-6A rod has met the chemical composition requirements of A-No. 1 (SFA-5.18/SFA-5.18M).
-Added optional supplemental designators to indicate ranges of shielding gases for which an electrode meets the requirements for classification, including any optional, supplemental designators. This resolves major issues previously associated with determining the A-No. for these filler metals.

On Wednesday, 10 July 2019 at 08:48:11 UTC+5:30 dili...@gmail.com wrote:
ER70S-6 chemical composition does not allow A-No allocation. 

Στις Πέμ, 6 Ιουν 2019, 14:40 ο χρήστης Revdiwala Darshan <darshanm...@gmail.com> έγραψε:
Please refer QW-404.12 (f) for code restriction.

Regards,
Darshan

On Mon, 3 Jun 2019, 6:26 pm Kannayeram Gnanapandithan, <kgpan...@gmail.com> wrote:
Code doesn't restrict but u will not get it in cut to length. Hardness will also increase due to more Mn, Si. It is better to add ER 70S3

On Mon, 3 Jun 2019 7:48 pm K K, <kara...@gmail.com> wrote:
Dear All,

My PQR is qualified with ER70S-2.

Can I use ( Mention) ER70S-6 in WPS.

Regards
Kiran


--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/4955a6fe-a91e-4b08-8f15-5aaa363df01cn%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAJzm4eMERRAgCM63OVeadMEY05XjnNYezLwdtGSK9kea%3DPvdtQ%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more