Re: Re: [MW:28480] Re: Difference between the electrode E8018 B-8 & E8015 B-8

without leaving room for confusion and as mentioned earlier trailing mail CVN is not applicable in your case, go ahead without qualifications.

Regards,

Muneeb.M

From: sandeep kumar
Date: 2018-10-22 10:29
To: Materials & Welding
Subject: [MW:28470] Re: Welding Electrodes
E8016-B2 is having increased Cr. compare to E8016-B1.
Please elobrate more, what is the reason for change & any code compliance applicable.

According to ASME section IX, QW 404.12 its a supplementary essential variable and require re-qualification if you have CVN requirements.

Thanks & regards
Sandeep Kumar

From: muneebslsa@gmail.com
Date: 2018-10-18 16:14
To: materials-welding
Subject: Re: [MW:28435] Re: Difference between the electrode E8018 B-8 & E8015 B-8

Dear expert,

can we use welding electrodes E8016-B2 instead of E8016-B1?

Answer: change in classification is falling under supplementary essential variable and your case can be used as per QW-404.12, which does not clash with a to f.

Can any body differentiate between the electrodes E8018 B-8 & E8015 B-8, and the difference of applicable areas.
Answer:
A5.5 A5.5M Type of Covering Welding Positionsfor Classification(B) Type of Current(C)
E8015-X E5515-X Low hydrogen sodium F, V, OH, H dcep
E8018-X E5518-X Low hydrogen potassium, iron powder(F) F, V, OH, H ac or dcep

Regards,
M.Muneeb.

From: mathafiza
Date: 2018-10-17 04:08
To: Materials & Welding
Subject: [MW:28435] Re: Difference between the electrode E8018 B-8 & E8015 B-8
Dear expert,

can we use welding electrodes E8016-B2 instead of E8016-B1?

On Saturday, January 5, 2013 at 1:50:29 PM UTC+8, Biplab Pal wrote:
Dear Experts,

Can any body differentiate between the electrodes E8018 B-8 & E8015 B-8, and the difference of applicable areas.

--
Thanks & Regards
Biplab Pal
Welding Inspector

E-mail: bipla...@gmail.com

Information in this email and any attachments is confidential and intended solely for the use of the individual(s) to whom it is addressed or otherwise directed. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the Company. Finally, the recipient should check this email and any attachments for the presence of viruses. Myself accepts no liability for any damage caused by any virus transmitted by this email.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
Visit this group at https://groups.google.com/group/materials-welding.
For more options, visit https://groups.google.com/d/optout.

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog