Skip to main content

[MW:798] Re: Dissimilar Group number/Thickness combination PQR as per QW403.5/QW403.6

By Materials & Welding
Min qualified thickness can't be 1.5mm, when impact testing required.
Qualified thk range for P1G1 will be 6-12mm and P1G2 would be 12-24mm,
please refer the question again.

Dissimilar thickness combinations are quite common to qualify (in
particular for SR nozzle welds on equipment) per QW202.4

-----Original Message-----
From: Quality [mailto:quality@gpsoman.com]
Sent: Tuesday, May 27, 2008 10:28 AM
To: materials-welding@googlegroups.com
Subject: Re: [MW:797] Re: Dissimilar Group number/Thickness combination
PQR as per QW403.5/QW403.6


The qualified thickness range is 1.5mm to 12mm (2T) for P1G1to them
selves,
P1G2 to themselves & P1G1 to P1G2 combinations.

The maximum qualified weld deposit is 2t (to is deposited weld thickness

during the qualification).

If you qualify a procedure with different parent material thickness
(groove
weld), the thickness T can be considered based upon the tensile specimen

thickness (T) used for the destructive testing of the groove weld PQR.
In
short, qualification of different thickness of relatively less use in
ASME
Sec IX.

Normally none of the construction/ fabrication codes does not allow
difference in thickness more than 1.5T (of the thinnest). Any Thickness
welded above 1.5 will not be accounted in design.

Regards,
Sanjeevan
GPS


--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more