Re: [MW:29963] RE: 29899] Material selection for Desalination plants and brinesolution

Duplex grades

Ramin Kondori

Sr. QA/QC & Welding Engineer

-----------------------------------------------------------

PG-Dip. in Welding Engineering (IWE AT 0070)

BSc. in Civil Engineering (IUT)

BGAS Painting Inspector

ASNT Level I&II

On Sat, Aug 17, 2019 at 7:43 AM anjansaini <anjansaini@gmail.com> wrote:

CS with rubber lining and monel or non metallic (GRE/FRP/HDPE)
titanium would be costly

On Wed, Aug 14, 2019 at 4:54 PM Dhanabal Jalachandran <dhanabal.jalachandrann@gmail.com> wrote:
Dear Friend,

Stainless steels are the most widely used material in desalination plants. The ideal material for use in desalination plants is titanium because it suffers little to no corrosion in saltwater environments. However, titanium is far more expensive than stainless steels. There are advancements being made to improve the corrosion resistance of stainless steels. Highly alloyed ferritic and austenitic stainless steels are being tested in salt water in comparison to titanium. The stainless steels are normally alloyed with chromium, nickel, molybdenum, and nitrogen to improve their corrosion resistance.

Br
Dhanabal Jalachandran

Sent from Mail for Windows 10

From: Hrushikesh Sangamnerkar
Sent: 30 July 2019 18:38
To: Materials & Welding
Subject: [MW:29899] Material selection for Desalination plants and brinesolution

Dear expert,

Which material is suited to desalination plants keeping in mind the corrosion resistant properties?

Will titanium work well?

If any references or process licensors data available specifically for these applications do share.

Regards,
--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAMpWL2oWhhDc7Db7kUtwjBrNNrZCuY7-nJ%3DLisuw0s80oup9Cw%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/5d540296.1c69fb81.aaf7f.5383%40mx.google.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CA%2B2zReThcTcNyBD456A4NJV5bRuL2btmF3BJHuWw-t3ben511A%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAEagfUhM3e_zdijGnfRX-ypTwOW%3D7qnByeXBpi9yhT-oxE2SZA%40mail.gmail.com.

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog