Skip to main content

[MW:19661] Re: 19659] ASTM 815 grade S31803 chemical comosition

By Materials & Welding
Dear Colleagues,

i got a reply for my issue for your information,When there is an ellipsis (...), that means there is no requirement. The sample can have any concentration and it does not cause a non conformance.




On Fri, Dec 20, 2013 at 2:45 PM, Ezat Adel <ezatadel2008@gmail.com> wrote:
Dear Udit Maheshwari,

check the attached extract page from A815 document which stated that the fitting material shall conform to the chemical requirement in table 1 
for your advice 


On Fri, Dec 20, 2013 at 2:44 PM, Ezat Adel <ezatadel2008@gmail.com> wrote:


---------- Forwarded message ----------
From: Udit Maheshwari <udit.maheshwari@eil.co.in>
Date: Fri, Dec 20, 2013 at 10:21 AM
Subject: RE: 19659] ASTM 815 grade S31803 chemical comosition
To: Ezat Adel <ezatadel2008@gmail.com>


Dear Sir

 

You can check table 3 , if tolerances are under limit you can accept it

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Ezat Adel
Sent: Friday, December 20, 2013 12:16 PM
To: materials-welding
Subject: [MW:19659] ASTM 815 grade S31803 chemical comosition

 

Dear colleagues,

 

could you please check attached for ASTM 815 grade S31803 and advice me

what does the ellipsis(....) indicate to ,it means there is no CU% ,TI% content it means 0% content or it means it is not specified.

 

my issue i have a MTC which contain some of Ti%,Cu%,AL% and V% content

if this new product considered accept or not.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

MAIL HAS BEEN SCANNED BY MCAFEE e-APPLIANCE

The Mail has been scanned by Mcafee Appliance ********************************SAVE A TREE!***************************************** Please print only when necessary; avoid unnecessary prints and save the environment.


********************************DISCLAIMER*******************************************
"The contents of this E-mail (including the contents of the enclosure/(s) or attachment/(s) if any ) are privileged and confidential material of ENGINEERS INDIA LIMITED (EIL) and should not be disclosed to, used by or copied in any manner by anyone other than the intended addressee/(s). If this E-mail (including the enclosure/(s) or attachment/(s) if any ) has been received in error, please advise the sender immediately and delete it from your system. The views expressed in this E-mail message (including the enclosure/(s) or attachment/(s) if any) are those of the individual sender, except where the sender expressly, and with necessary authority, states them to be the views of EIL."



Dear Udit Maheshwari,

check the attached extract page from A815 document which stated that the fitting material shall conform to the chemical requirement in table 1 
for your advice 


--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
http://www.linkedin.com/groups/MaterialsWelding-122787?home=&gid=122787&trk=anet_ug_hm
 
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more