Skip to main content

Re: [MW:34790] RE: 34785] clarification require for WPS & PQR qualification with impact test

By Materials & Welding
Thanks for your reply.
With the same criteria what will be the qualified Base metal and Thickness qualification for Welder performance qualification (WPQ) and what should be minimum weld deposit to be made if I use 2 welders for the same Test coupon.

On Sat, 2 Mar 2024, 10:59 am DEEPAK KASHYAP, <welding@atvprojects.co.in> wrote:

Dear Mr. Gopalkrishnan,

 

 

As per your query, below are the answers:-

 

  1. The Qualified thickness range of the WPS with impact testing will be Min. 16 to  Max 40 mm (because your weld deposit thickness t will be 20 mm)----refer QW 403.6 and Table QW 451.1
  2. The Group on.  (P1G2 to IS2062 E350C) shall be considered along with above qualified thickness range. ----- refer QW 424.1 and Joule values depends on the Material code/Construction code.
  3. Yes, but it is for welder qualification Not for Procedure. --------- refer Table QW 452.1(b)

 

Thanks

 

From: materials-welding@googlegroups.com <materials-welding@googlegroups.com> On Behalf Of Gopalakrishnan G
Sent: Friday, March 1, 2024 6:18 PM
To: materials-welding@googlegroups.com
Subject: [MW:34785] clarification require for WPS & PQR qualification with impact test

 


dear expert

we have to do qualification wps ,pqr for the below mentioned materials as per ASME section 9.

 

Test coupon

SA 516 Gr 70 (P-1 G-2) -Thickness 20 mm

with

IS 2062 E 350 C (Unassigned Metal) - Thickness 50 mm

Code - ASME 

Position - 3G

Process - SMAW 

Electrode - E-7018

Impact =  -20C @ 27J

 

Question

1) what is the minimum & maximum thickness qualified with impact?(code reference).

2) what has to be considered during and after impact results?(comparing with base metals)

3) Whether Thickness "t" weld metal deposit in coupon should be 13 mm or 3 layer minimum in single side to qualify for maximum to be welded ? 

 

Thanks in advance.Do the needful. 

 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAOp_kKgYrfxS7%2B7LOv5Ow4R%2B1d8WVXgURzsy_NMJZ26nobS9kg%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/002801da6c5e%246be31220%2443a93660%24%40atvprojects.co.in.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAOp_kKjOkag1RBqNbsZusnVr5SJ5SNZFX582mQ1i5LtaVKWkeA%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more